Federal Communications Commission Statement
This device complies with FCC Rules Part 15. Operation is subject to the following two conditions:
* This device may not cause harmful interference.
* This device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. If this
equipment is not installed and used in accordance with the manufacturer's instructions, it may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
* Reorient or relocate the receiving antenna.
* Increase the separation between the equipment and receiver.
* Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
* Consult the dealer or an experienced radio/TV technician for help.
The use of shielded cables for connection of the monitor to the graphics card is required to assure
compliance with FCC regulations. Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user's authority to operate this equipment.
Canadian Department of Communications Statement
This digital apparatus does not exceed the Class B limits for audio noise emissions from digital apparatuses
set out in the Radio Interference Regulations of the Canadian Department of Communications.
Manufacturer's Disclaimer Statement
The information in this document is subject to change without notice and does not represent a commitment
on the part of the vendor. No warranty or representation, either expressed or implied, is made with respect to the
quality, accuracy or fitness for any particular purpose of this document. The manufacturer reserves the right to
make changes to the content of this document and/or the products associated with it at any time without obligation
to notify any person or organization of such changes. In no event will the manufacturer be liable for direct, indirect,
special, incidental or consequential damages arising out of the use or inability to use this product or documentation,
even if advised of the possibility of such damages. This document contains materials protected by copyright. All
rights are reserved. No part of this manual may be reproduced or transmitted in any form, by any means or for any
purpose without expressed written consent of it's authors. Product names appearing in this document are mentioned
for identification purposes only. All trademarks, product names or brand names appearing in this document are
registered property of their respective owners.
Printed in Taiwan.
Apr 2003
OST-CONSUMER
RECYCLED PAPER
100%
TABLE OF CONTENTS
Chapter 1
Introduction ...............................................................1
1-1 Product Specifications..................................................................................... 1
1-2 Package Contents ............................................................................................ 3
1-3 CHAINTECH’s Special Features:................................................................... 4
1-4 9CJS Motherboard Diagram............................................................................ 5
1-5 9CJS Motherboard Layout .............................................................................. 6
Chapter 2
Hardware Setup.........................................................7
2-1 Installing a CPU Processor for Socket 478 ..................................................... 7
2-2 Setting your CPU’s Parameters ....................................................................... 8
2-3 Main Memory Configuration .........................................................................11
2-4 Connector and Jumper Reference Chart ....................................................... 15
2-5 Connector and Jumper Settings..................................................................... 16
2-6 Serial ATA and Parallel ATA......................................................................... 26
2-7 CBOX™ 3 Setup........................................................................................... 28
2-8 Handigator: Function List ............................................................................. 29
2-9 CMC (Chaintech Multimedia Card) Setup ................................................... 30
Chapter 3
BIOS Setup Program ..............................................32
3-1 Standard CMOS Setup .................................................................................. 33
3-2 Advanced BIOS Features .............................................................................. 34
3-3 Advanced Chipset Features........................................................................... 37
3-4 Integrated Peripherals.................................................................................... 39
3-5 Power Management Setup............................................................................. 43
3-6 PNP/PCI Configurations ............................................................................... 46
3-7 PC Health Status............................................................................................ 47
3-8 Frequency/Voltage Control ........................................................................... 48
3-9 Load Fail-Safe Defaults ................................................................................ 49
3-10 Load Optimized Defaults ............................................................................ 49
3-11 Supervisor Password & User Password Setting .................................................. 49
3-12 Save and Exit Setup..................................................................................... 50
3-13 Exit Without Saving .................................................................................... 50
Chapter 4
DRIVER Setup ........................................................51
4-1 Intel® IDE Bus Mastering Drivers Setup ..................................................... 51
