background image

4

3.2

   Press the remote control push button 

to close the door. The door will not 
move more than an inch (2.5 cm), and 
the garage door opener lights will fl ash 
10 times.

Test the Protector System

®

3.1

   Open the door. Place the garage door 

opener carton in the path of the door.

The garage door opener will not close from 
a remote control if the LED in either safety 
reversing sensor is off (alerting you to the fact 
that the sensor is misaligned or obstructed).

If the garage door opener closes the door when 
the safety reversing sensor is obstructed (and 
the sensors are no more than 6 inches [15 cm] 
above the fl oor), call for a trained door systems 
technician.

3

2.1

   With the door fully open, place a 

1-1/2 inch (3.8 cm) board (or a 2x4 laid 
fl at) on the fl oor, centered under the 
garage door.

Test the Safety Reversal System

2.2

   Press the remote control push button 

to close the door. The door MUST 
reverse when it makes contact with the 
board.

If the door stops and does not reverse on the 
obstruction, increase the down travel (refer to 
Adjustment Step 1). 

Repeat the test. When the door reverses upon 
contact with the 1-1/2 inch board, remove the 
board and open/close the door 3 or 4 times to 
test the adjustment.

If the test continues to fail, call a trained door 
systems technician.

Without a properly installed safety reversal 
system, persons (particularly small 
children) could be SERIOUSLY INJURED or 
KILLED by a closing garage door. 
•   Safety reversal system MUST be tested 

every month.

•   After ANY adjustments are made, the 

safety reversal system MUST be tested. 
Door MUST reverse on contact with 
1-1/2" high (3.8 cm) object (or 2x4 laid 
fl at) on the fl oor.

2

Without a properly installed safety 
reversing sensor, persons (particularly 
small children) could be SERIOUSLY 
INJURED or KILLED by a closing garage 
door. 

Synchronize the Door Control

4

To synchronize the door control to the garage door opener, press the push bar until the garage door opener activates (it may take up to 3 presses). Test the door control by pressing the push bar, each 
press of the push bar will activate the garage door opener.

Summary of Contents for 050ACTWFLK













Reviews: