CLICKER
®
MODEL KLIK1U
Universal Garage Door Opener Remote Control
To prevent possible SERIOUS INJURY or DEATH from a moving gate or garage door:
• ALWAYS keep remote controls out of reach of children. NEVER permit children to
operate, or play with remote control transmitters.
• Activate gate or door ONLY when it can be seen clearly, is properly adjusted and
there are no obstructions to door travel.
• ALWAYS keep gate or garage door in sight until completely closed. NEVER permit
anyone to cross path of moving gate or door.
© 2008, Clicker Corporation
114A3485C
All Rights Reserved
Read instructions thoroughly BEFORE beginning.
Start with garage door closed. Identify garage door opener type -Smart/Learn
button or DIP Switch. Smart/Learn button or DIP Switches are located on motor
unit or external receiver. Refer to owner’s manual if necessary.
Clicker products are intended to be used only with garage door openers
manufactured after 1993 that utilize photo-eyes safety sensors. These are
always located on or near the bottom of the door track. If your garage door
does not have the sensors attached and working, the opener is not
compliant with current federal safety regulations and should be replaced.
Proceed with instructions according to your type of garage door opener.
ON
2
3
1
KG
KG
NOTE:
2 Position DIP
Switch:
If programming fails reverse
DIP switches (OFF to ON and
ON to OFF).
**3 Position DIP Switch:
For Chamberlain remotes DO NOT
use the “0” position, use “+” or “-”.
If you already have a 3-button
remote, DIP switch #1 must be set to
“-” if the large button is to open the door. It may be
necessary to reprogram original remote controls.
2
12
11
10
9
8
5
3
7
6
4
1
2
Clicker Remote
Existing Remote
3
4
Press program button
until LED lights.
5
Match DIP switches. Turn
extra switches OFF.**
OR
DIP SWITCH
SMART/LEARN BUTTON
2
3
1
KG
KG
4
Motor Unit
Select a button to program.
Press button times
ensuring LED stops
flashing after each press.
Code is accepted when
door activates.
REMOTE CONTROL BATTERY
NOTICE: To comply with FCC and or Industry Canada (IC) rules, adjustment or modifications of this
receiver and/or transmitter are prohibited, except for changing the code setting or replacing the battery.
THERE ARE NO OTHER USER SERVICEABLE PARTS.
Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Dispose of batteries properly. Replace ONLY with 3V2032
coin batteries.
To prevent possible SERIOUS INJURY or DEATH:
• NEVER allow small children near batteries.
• If battery is swallowed, immediately notify doctor.
To reduce risk of fire, explosion or chemical burn:
• Replace ONLY with 3V2032 coin batteries.
•
Do NOT recharge, disassemble, heat above 100°C (212°F) or
incinerate.
CHART B
# of
Brand
Description
Year
times to
press
button
11 Chamberlain
®
* 9
Position ‘90-’92
12 Chamberlain
®
* 9
Position
Canada
‘83-’89
13 Genie
®
12
Position
‘85
14 Linear
Multicode
®
10
Position ‘76
15 Chamberlain
®
8
Position
‘83-’89
16 Stanley/Multicode
®
10
Position
‘76
17 Genie
®
9
Position
‘85
18 Linear
®
Moore-O-Matic
®
8
Position ‘76
19 Chamberlain
®
* 7
Position ‘83-’89
CHART A
# of
Brand
Type/Color of
Year
times to
Smart/Learn
press
button
1 Linear
®
Mega-Code
‘97-Current
2 Chamberlain
®
* Orange/Red ‘97-’03
3 Chamberlain
®
* Purple
‘95-’Current
4 Chamberlain
®
* Green
‘93-’96
5 Genie
®
Overhead
Door
®
Intellicode
‘95-’05
6 Genie
®
Overhead
Door
®
Intellicode
‘05
Current
7 Stanley
®
Secure
Code
‘98
9 Wayne
Dalton
®
Rolling
Code ‘99
11 Chamberlain
®
* 9
Position ‘90-’92
1-800-442-1255
Chamberlain, LiftMaster and Moore-O-Matic are Trademarks of Chamberlain Group. Genie
is a Trademark of Overhead Door Corporation. Overhead Door is a Trademark of Overhead
Door Corporation. Linear is a Trademark of Linear Corporation. Master Mechanic is a
Trademark of TruServ. Sears is a Trademark of Sears & Roebuck. Stanley is a Trademark
of The Stanley Works. Wayne Dalton is a trademark of Wayne Dalton Corporation. Do It is
a trademark of Do It Best Corporation.
Press program button.
6
7
Programming complete.
Press selected button to
test. If unit does not work,
return to Step 3.
Press and release the
smart/learn button.
5
1
See Chart B to
determine # of times to
press button and write
in blank on step 5.
DIP SWITCH
SMART/LEARN BUTTON
Press program button.
6
7
3
Press program button until
LED lights.
2
1
See Chart A to
determine # of times to
press button and write
in blank on step 5.
NOTE:
Your opener may
appear different and you
may have to remove the
light lens to access the
learn button.
*NOTE:
LiftMaster, Do-It, Master Mechanic, Raynor, True Value and Sears Craftsman are compatible
with Chamberlain technology.
OR
OR
Click
www.clickerproducts.com
12
11
10
9
8
5
3
7
6
4
1
2
LED Indicator
Button 1
Button 2
Program Button
Battery
DIP Switches
Battery Cover
Motor
Unit
ON
STOP
NOTE:
If there are
problems programming to
button 1, program to
button 2.
Select a button to program.
Press button times
ensuring LED stops
flashing after each press.
Code is accepted when
one of the following
occurs:
Programming complete.
Press selected button to
test. If unit does not work,
return to Step 3.
