18
SINGLE BUTTON REMOTE CONTROL PROGRAMMED
AS A SINGLE BUTTON CONTROL (SBC)
This function programs a remote control as a wireless single
button control. This function will work in the following modes:
In B2 mode, operation is OPEN/STOP/CLOSE/REVERSE/STOP.
In C2 mode, operation is OPEN/STOP/constant pressure to
CLOSE/STOP on release.
In T and TS modes, operation is
OPEN/STOP/CLOSE/REVERSE/STOP and Timer to Close
start/refresh.
NOTE:
If Car Dealer mode is enabled, SBC will be
open only stopping at the Open Mid-Stop.
In FSTS mode, operation is OPEN with Timer to Close
start/refresh only, bypassing a programmed Open Mid-Stop.
1. Press and release the RADIO button on the logic board (LED
will light).
2. Press and release the SBC externally wired button or TIMER on
the logic board (LED flashes rapidly and then remains on
solid).
3. Press and hold the remote control button until the LED flashes
rapidly. The LED will then remain on silid after releasing.
4. Press and release the RADIO button on the logic board (LED
flashes rapidly and then turns off). The programming mode is
exited if no activity is performed within 30 seconds.
NOTE:
Requires self-monitoring photo eyes when using constant
pressure to close (wiring C2, D1 and E2 ).
ERASING REMOTE CONTROLS
Press and hold the RADIO button on the logic board until the
RADIO LED flashes rapidly (approximately 5 seconds).
All remote controls will be erased.
STANDARD SINGLE BUTTON REMOTE CONTROL
Built in 3-channel, 315MHz radio receiver allows you to add
as many as 23 Security
✚
®
remote controls or dip switch
remote controls.
PROGRAMMING REMOTE CONTROLS
STANDARD SINGLE BUTTON REMOTE CONTROL
1. To enter programming, press and release the RADIO button on
the logic board (LED will light).
2. Press and hold the remote control button until the LED flashes
rapidly, then release remote control button. The LED will then
remain on solid after releasing the button. Repeat to add
additional remote control(s).
3. Press and release the RADIO button to complete the
programming. The programming mode is exited if no activity is
performed within 30 seconds.
NOTE:
Single button remote control is not supported with D1 and
E2 wiring modes.
P R O G R A M M I N G
To prevent possible SERIOUS INJURY or DEATH, install
reversing sensors when the 3-button control station is out of
sight of the door or ANY other control (automatic or manual) is
used. Reversing devices are recommended for ALL installations.
ATTENTION
AVERTISSEMENT
AVERTISSEMENT
AVERTISSEMENT
WARNING
WARNING
CAUTION
WARNING
WARNING
PRECAUCIÓN
ADVERTENCIA
ADVERTENCIA
ADVERTENCIA
L i f t M
a s t e
r
U1
MRT
1
RADIO
MID
2
T
E2
RELA
RELA
D1
C2
B2
OLS
MID
SLS
RE
V
CLS
D25
D24
D26
D27
D36
C77
C73
C54
C78
L1
L5
P6
D35
D16
P7
K3
FAILSAF
X1
E1
R29
C11
D3Ø2
P4
Ø14LGØ6
C71
®
RADIO
NOTICE: To comply with FCC and or Industry Canada (IC) rules, adjustment or modifications of this
receiver and/or transmitter are prohibited, except for changing the code setting or replacing the
battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.
Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation.
Summary of Contents for H
