13
I N S TA L L I N G T H E R E C E I V E R
To prevent possible SERIOUS INJURY or DEATH from a moving
gate or garage door:
• ALWAYS keep remote controls out of reach of children.
NEVER permit children to operate, or play with remote control
transmitters.
• Activate gate or door ONLY when it can be seen clearly, is
properly adjusted, and there are no obstructions to door travel.
• ALWAYS keep gate or garage door in sight until completely closed
NEVER permit anyone to cross path of moving gate or door.
WARNING
CAUTION
WARNING
WARNING
ATTENTION
AVERTISSEMENT
AVERTISSEMENT
AVERTISSEMENT
HIGH
SECURITY MODE
Security Mode
Terminals
Jumper
NORMAL
SECURITY MODE
Security Mode
Terminals
Jumper
FIGURE 2
NOTICE: To comply with FCC and or Industry Canada (IC) rules, adjustment or modifications of
this receiver and/or transmitter are prohibited, except for changing the code setting or replacing
the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.
Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation.
WIRING THE RECEIVER
Contacts 1 and 2 on the receiver terminal strip are for power. The
power terminals are unpolarized. Connect terminals 1 and 2 to
the accessory power terminals on the S4 terminal strip at the
bottom of the logic board (Figure 1).
Contacts 3 and 4 on the receiver terminal strip are for a common
and a relay. Connect terminals 3 and 4 to terminals 1 and 10 on
the S5 terminal strip at the top of the logic board.
SET SECURITY MODE
The Universal Receiver can be used with up to 15 rolling code
remotes or passwords in HIGH security mode. Alternately, it can
be used with up to 31 of any type remote in NORMAL security
mode, including any combination of rolling code, billion code, or
dip switch remotes.
The jumper must be set at the HIGH position for the receiver to
operate in HIGH security mode. It must be set at NORMAL
position to operate at the NORMAL mode (Figure 2).
When changing from NORMAL to HIGH security mode, any
previous remote codes must be erased. Repeat Steps 2 and 3 in
the Programming Section below to reprogram the receiver for
each remote control in use.
The receiver is factory set at HIGH.
PROGRAMMING THE REMOTE TO THE RECEIVER
STEP 1:
Pry open the front panel of receiver case with a coin or
a screwdriver. Re-connect power to opener (Figure 3).
STEP 2:
Press and release the “learn” button on the receiver.
The learn indicator light will glow steadily for 30 seconds.
STEP 3:
Within 30 seconds, press and hold the button on the
hand-held remote that you wish to operate your gate.
The opener will now operate when the push button on either the
receiver or the remote control is pressed.
Repeat Steps 2 and 3 for each remote control that will be used to
operate the gate.
TO ERASE ALL REMOTE CONTROL CODES
Press and hold the “learn” button on the receiver panel until the
indicator light turns off (about 6 seconds). All remote codes are
now erased. Then follow the steps above to reprogram each
remote control.
24V 12V
HIGH NORM
C
P2
M
Learn Button
Indicator Light
Output Duration
Terminals
Security Mode
Power Supply
Jumper
OPEN RECEIVER
FIGURE 3
OPENING RECEIVER
Connect
Antenna
(Not
Provided)
ACC+
BAT– BAT
BAT–
BAT+
ACC–
J4
Jumper P1 to J4 Accessory Power
Jumper P2 to J4 Accessory Power
Jumper P3 to J5 Terminal 1
Jumper P4 to J5 Terminal 10
1
2
3
4
5
6
7
8
9
10
11
J5
2
3
4
1
+
10
–
1
FIGURE 1
Summary of Contents for LIFTMASTER PROFESSIONAL MSLDCBB
Page 18: ...18 OPERATOR NOTES...
