background image

(You must read, understand and agree with all items in the limited warranty)

Installation check off list must be completed.

Any required contact edges and photo beams must be installed.

LiftMaster 

warrants the MEGA SLIDE UL to be free of defects in workmanship and materials for a period of 2 years for electronics and

mechanical components and includes a 10 year corrosion perforation warranty on the cover and chassis (Cosmetic appearance is not
included). Warranty will begin from the date of purchase.

LiftMaster reserves the right of final determination as to the existence and causes of any defect or failure. Any part or parts found to be
defective and are returned to LiftMaster within the warranty period, shall at our option be repaired or replaced free of charge F.O.B. the
factory. Freight is not included at any time on gate arms and chassis. ONLY UPS ground freight is included during the first year of
warranty.

The warranty will not apply the following circumstances which are considered beyond our control.

Mis-use, vandalism, accident, neglect, unauthorized repairs or modifications, acts of God (lightning, floods, insect damage, etc.), power
surges, units subjected to corrosive environments, incorrect installation or application, the batteries or incorrect battery installation,
operation without or failure to use correct battery type, damage to mechanism due to wrong type of gate, incorrect weight, gate not
operating freely or not on level ground.

The warranty set forth above is entirely exclusive and no other warranty whether written or oral, is expressed or implied. LiftMaster,
inc. specifically disclaims any and all implied warranties, merchantability or fitness for a particular purpose. It is the purchaser’s sole
and exclusive responsibility to determine whether or not the equipment will be suitable for a particular purpose. In no event shall
LiftMaster, inc. be held liable for direct, indirect, incidental, special, consequential damages or loss of profits whether based on
contract, tort, or any other legal theory during the course of the warranty or at any time there after. The installer and/or end user do
agree to assume all responsibility for all liability in use of this product, releasing LiftMaster of all liability.

WARNING: MEGA SLIDE UL IS NOT FOR USE WITH MOTOR CYCLES, BICYCLES OR PEDESTRIANS. YOU MUST PROVIDE
APPROPRIATE SIGNAGE BEFORE ACTIVATING THE UNIT. NEVER ALLOW CHILDREN TO PLAY NEAR OR OPERATE AUTOMATIC
GATES. INSTALL PHOTO BEAMS AND PRESSURE SENSING EDGES AT ANY AREA THAT COULD POSE A HAZARD TO PEDESTRIAN OR
VEHICULAR TRAFFIC.

IN ORDER TO INSTALL AND USE THE MEGA SLIDE UL, YOU MUST UNDERSTAND AND BE IN FULL UNCONDITIONAL AGREEMENT
WITH ALL STIPULATIONS OUTLINED ABOVE. IF YOU ARE NOT IN FULL AGREEMENT, DO NOT PUT UNIT INTO OPERATION. IF
OPERATOR IS PUT INTO OPERATION THIS WILL BE CONFIRMATION THAT YOU ARE IN FULL UNCONDITIONAL AGREEMENT WITH
ALL OF THE ABOVE STIPULATIONS.

Materials, components, features and specifications are subject to change without notice.

19

L I M I T E D   W A R R A N T Y

Summary of Contents for LIFTMASTER PROFESSIONAL MSLDCBB





















Reviews: