background image

       9/16 en

PROGRAM INTERNET GATEWAY myQ

Using the RESET -Button on the control board

1. Connect the ethernet cable to the LiftMaster Internet Gateway 

    and the router.

2. Connect power to the LiftMaster Internet Gateway.

3. Create an online account on the latest Liftmaster MyQ smartphone

    application or on www.liftmaster.eu. It is recommended to use the

    smartphone as it will allow you to stand close to the gate while programming

4. Register the LiftMaster Internet Gateway.

5. Click on „Add new device“ and follow the steps given by the

    application or on the webpage.

6. Note: When pushing the RESET-Button you will hear a beep and the

    LEDs CH1 and CH2 

 rst go on, then after matching, the LEDs will

    blink 3 times and go out.

7. The App will tell you if programming was successful and will prompt

    you to assign a name to the gate.

PROGRAM DOOR MONITOR

Using the RESET -Button on the control board

1. Connect power to the door monitor.

    Position the door monitor in a convenient visible place inside the house.

    If this place is too far from the gate opener the connection may not be

    possible or is often interrupted.

    Choose a more convenient place.

2. Press and release the „LEARN“ button on the back of the door monitor.

    Red and green LED blink alternately.

    Within 60 seconds press and release the RESET button on the control board.
    To con

 rm programming red and green LED on the door monitor are on.

DELETE DOOR MONITOR

Press the „LEARN“ button on the back of the door monitor for at least 10 sec.

A short „beep“ con

 rms that deleting was successful.

RADIO MODULE

RADIO MODULE

Summary of Contents for LYN300 Series




















Reviews: