background image

DIP SETTINGS

1 / 2 Motor

Select if 1 or 2 motors are connected to the control board

OFF:  

2 Motors connected

ON:  

1 Motor connected

OPEN/STEP

Changes the programming and reaction of the gate on commands.

For the use with loop detectors please refer to the loop detector

instruction

 rst.

Step Mode: The gate starts to open if a command is received, next

stop, next closes, next stop, next open…….

OPEN Mode: The gate will not react on a command during the travel

to the gate open position.

OFF:  

STEP

ON:  

OPEN

LIGHT/SPY

Gate Monitoring / yard Lighting Select if the function is used or leave free.

OFF: LIGHT(yard lighting)

ON: SPY (gate monitoring)

OBSTACLE

Factory-equipped with wire jumper. Disabling increases the

operating power at the control. CAUTION: If the jumper is

disabled, the door system should be secured with additional

safety devices (contact strip, etc.).

LOOP/EDGE

Select for desired device.

OFF:  

EDGE

ON:  

LOOP

SPEED

Select for the type of motor you intend to use.

OFF:  

Slow ART, LYN, SCS, SUB

ON:  

Fast LYN, SCS, SUB

RADIO

The DIP “RADIO” is required to program remote controls.

For programming procedure please refer to page 8, section “radio”

OFF:  

No programming of remote controls possible

ON:  

Programming of remote controls possible

Important: Switch off DIP “RADIO” if not in use!

Wing Delay Adjustment

The delay of one wing is required to open and close the wings correctly

and to operate the wings with a safe distance from each other. A larger

distance may be required when the mechanical installation distances

are different between the wings or wing length is different. The delay

time in opening direction is 

 xed. The closing is adjustable

Push P3 and P1 together and hold for approx 5 seconds, and count

the number of clicks you hear. The click sound is produced from a

relay (light relay).

1 click = small delay, about 4÷8 seconds (factory default settings)

2 click = medium delay, about 8÷12 seconds

3 click = big delay, about 12÷16 seconds

4 click = total delay, wing 1 will close only when wing 2 is completely closed 

Delay in opening direction is always 3 to 5 seconds.

5 click = no delay in opening and closing (wings move simultaneously)

Repeat the procedure if required.

       11/16 en

RADIO MODULE

RADIO MODULE

ON

ON

Summary of Contents for LYN300 Series




















Reviews: