background image

19

  

REV 71531-20140505

ENGLISH

 

71531

MAINTENANCE AND STORAGE

Storage

The generator should be started at least once every 14 
days and allowed to run for at least 20 minutes. For 
longer term storage, please follow these guidelines.

Generator Storage

1.  Add a properly formulated fuel stabilizer to the tank.
2.  Be sure all appliances are disconnected from the 

generator.

3.  Run the generator for a few minutes so the treated 

fuel cycles through the fuel system and carburetor.

4.  Turn the fuel valve to the “Off” position.
5.  Let the generator run until fuel starvation has 

stopped the engine. This usually takes a few minutes.

6.  The generator needs to cool acompletely before 

cleaning and storage.

7.  Clean the generator according to the maintenance 

section.

8.  Change the oil.
9.  Remove the spark plug and pour about 1⁄2 ounce 

(14.8 mL) of oil into the cylinder. Crank the engine 
slowly to distribute the oil and lubricate the cylinder.

10. Reattach the spark plug.
11. Store the unit in a clean, dry place out of direct 

sunlight.

Generator Battery

This product is equipped with an automatic battery 
charging circuit. The battery will receive charging 
voltage when the engine is running. The battery will 
maintain a proper charge if the unit is used on a regular 
basis (about once every two weeks). If it is used less 
frequently, the battery should be connected to a trickle 
charger or battery maintainer to keep the battery 
properly charged. If the battery is not able to start the 
engine, it can be started by manually pulling the engine 
recoil cord. If the battery voltage is extremely low, 
the charging circuit may not be able to re-charge the 
battery. In this case, the battery must be connected to a 
standard automotive style battery charger for re-charging 
before it can be used.

Disconnect the Battery

1.  Remove the protective cover from the black/negative 

battery lead.

2.  Disconnect the black/negative lead from the black/

negative terminal on the battery and store the cap 
screw (M5x10) and nut (M5).

3.  Repeat steps 1-2 for the red/positive battery lead.
4.  Store the battery in a cool, dry place.

A Float Charger will maintain the battery condition 
over long storage periods.

NOTE

Charge the Battery

For a generator equipped with batteries for electric 
starting, proper battery maintenance and storage should 
be followed. An automatic battery charger (not included) 
with automatic trickle charging capability should be used 
to charge the battery. Maximum charging rate should not 
exceed 1.5 amps. Follow the instructions included with 
the battery charger. The battery should be fully charged 
at least once per month.

Generator exhaust contains odorless and colorless 
carbon monoxide gas.

To avoid accidental or unintended ignition of your 
remote start generator during periods of storage, 
the following precautions should be followed:

 

– When 

storing the generator for short periods of 

time make sure that the Ignition Switch, the Fuel 
Valve and the Battery Switch are set in the 

OFF 

position. 

 

– When 

storing the generator for extended periods 

of time make sure that the Ignition Switch, the 
Fuel Valve and the Battery Switch are set in the 
the the 

OFF position and the battery leads have 

been 

disconnected from the battery. 

DANGER

Summary of Contents for 71531


































Reviews: