background image

REV 73536i-20130314  

24

73536i

 

ENGLISH

WARRANTy

WARRANTy

CHAMPION POWER EQUIPMENT

2 YEAR LIMITED WARRANTY

Warranty Qualifications

Champion Power Equipment (CPE) will register this 
warranty upon receipt of your Warranty Registration Card 
and a copy of your sales receipt from one of CPE’s retail 
locations as proof of purchase.
Please submit your warranty registration and your proof 
of purchase within ten (10) days of the date of purchase.

Repair/Replacement Warranty

CPE warrants to the original purchaser that the 
mechanical and electrical components will be free of 
defects in material and workmanship for a period of 
one year (parts and labor) and two years (parts) from 
the original date of purchase (90 days (parts and 
labor) and 180 days (parts) for commercial & industrial 
use). Transportation charges on product submitted 
for repair or replacement under this warranty are the 
sole responsibility of the purchaser. This warranty only 
applies to the original purchaser and is not transferable.

Do Not Return The Unit To The Place Of Purchase

Contact CPE’s Technical Service and CPE will 
troubleshoot any issue via phone or e-mail. If the 
problem is not corrected by this method, CPE will, at its 
option, authorize evaluation, repair or replacement of the 
defective part or component at a CPE Service Center. 
CPE will provide you with a case number for warranty 
service. Please keep it for future reference. Repairs 
or replacements without prior authorization, or at an 
unauthorized repair facility, will not be covered by this 
warranty.

Warranty Exclusions

This warranty does not cover the following repairs and 
equipment:

Normal Wear

Generators need periodic parts and service to perform well. 
This warranty does not cover repair when normal use has 
exhausted the life of a part or the equipment as a whole.

Installation, Use and Maintenance

This warranty will not apply to parts and/or labor if this 
generator is deemed to have been misused, neglected, 
involved in an accident, abused, loaded beyond the 
generator’s limits, modified, installed improperly or 
connected incorrectly to any electrical component. 

Installation, Use and Maintenance Cont’d. 

Normal maintenance such as spark plugs, air filters, 
adjustments, fuel system cleaning and obstruction due 
to buildup is not covered by this warranty.

Other Exclusions

This warranty excludes:

 

– Cosmetic defects such as paint, decals, etc.

 

– Wear items such as filter elements, o-rings, etc.

 

– Accessory parts such as starting batteries, and 

storage covers.

 

– Failures due to acts of God and other force majeure 

events beyond the manufacturer’s control.

 

– Problems caused by parts that are not original 

Champion Power Equipment parts.

This warranty does not apply to generators used for 
prime power in place of a utility.

Limits of Implied Warranty and Consequential Damage

Champion Power Equipment disclaims any obligation to 
cover any loss of time, use of this product, freight, or 
any incidental or consequential claim by anyone from 
using this generator. THIS WARRANTY IS IN LIEU OF 
ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, 
INCLUDING WARRANTIES OF MERCHANTABILITY OR 
FITNESS FOR A PARTICULAR PURPOSE. 
A unit provided as an exchange will be subject to the 
warranty of the original unit. The length of the warranty 
governing the exchanged unit will remain calculated by 
reference to the purchase date of the original unit.
This warranty gives you certain legal rights which may 
change from state to state. Your state may also have 
other rights you may be entitled to that are not listed 
within this warranty.

Contact Information

Address

Champion Power Equipment, Inc.
Customer Service
10006 Santa Fe Springs Rd.
Santa Fe Springs, CA 90670
www.championpowerequipment.com

Customer Service

Mon – Fri 8:30 AM – 5:00 PM (PST/PDT)
Toll Free: 1-877-338-0999
info@championpowerequipment.com
Fax no.: 1-562-236-9429

Technical Service

Mon – Fri 8:30 AM – 5:00 PM (PST/PDT)
Toll Free: 1-877-338-0999
tech@championpowerequipment.com
24/7 Tech Support: 1-562-204-1188

Summary of Contents for 73536i































Reviews: