background image

18

90720 - 7 TON FULL BEAM LOG SPLITTER

ASSEMBLY

Add Engine Oil

 

CAUTION

DO NOT attempt to crank or start the engine before it has been 
properly filled with the recommended type and amount of oil. 
Damage to the engine as a result of failure to follow these 
instructions will void your warranty.

 

NOTICE

The recommended oil type is 

10W-30 automotive oil

 

NOTICE

Once oil has been added, a visual check should show oil about 
1-2 threads from running out of the fill hole.

If using the dipstick to check oil level, DO NOT screw in the 
dipstick while checking.

 

NOTICE

Check oil often during the break-in period. Refer to the 
Maintenance section for recommended service intervals.

 

NOTICE

We consider the first 5 hours of run time to be the break-
in period for the engine. During the break in period we 
recommend using standard automotive non-synthetic blended 
oils. After the break in period synthetic lubricant can be used 
but is not required. Adjusting throttle setting will increase/
decrease engine speed helping to seat piston rings. Avoid 
bogging or lugging the engine down and avoid prolonged 
running at constant RPM. After the 5 hour break-in period, 
change the oil. Using synthetic lubricants does not increase 
the recommended oil change interval.

 

NOTICE

Weather will affect engine oil and engine performance. Change 
the type of engine oil used based on weather conditions to suit 
the engine needs.

 

NOTICE

Synthetic oil may be used after the 5 hour initial break-in 
period. Using synthetic oil does not increase the recommended 
oil change interval. Full synthetic 5W-30 oil will aid in starting 
in cold ambient < 41ºF (5ºC).

   -20

0

20

40

60

Ambient temperature

Recommended Engine Oil Type

80

100

120

         -28.9

°F
°C

       -17.8       -6.7         4.4

15.6      26.7    37.8

  48.9

10W-30

5W-30 Synthetic

10W-40

5W-30

1.  Place the log splitter on a flat, level surface.

2.  Remove oil fill cap/dipstick to add oil.

3.  Using a funnel, add up to 13.5 fl. oz (0.4L) of oil and replace 

oil fill cap/dipstick. DO NOT OVERFILL.

4.  Check engine oil level daily and add as needed.

MAX

MIN

OIL DIP STICK

Summary of Contents for 90720





































Reviews: