background image

EMISSION CONTROL SYSTEM WARRANTY

 

 
The following are specific provisions relative to your Emission Control System Warranty 
Coverage. 

 
Emission Control System Warranty (ECS Warranty): 

 
1. APPLICABILITY: 

The ECS Warranty Period shall begin on the date the new engine or equipment is 

delivered to its original, end-use purchaser, and shall continue for 24 consecutive months thereafter. 

 
2. GENERAL EMISSIONS WARRANTY COVERAGE 

 
CPE warrants to the original, end-use purchaser of the new engine or equipment and to each subsequent 
purchaser that each of its small off-road engines is: 

a. Designed, built and equipped so as to conform at the time of sale with applicable regulations 

under the Canadian Environmental Protection Act, 1999 (CEPA 1999).

 

b. Free from defects in materials and workmanship that cause the failure of a warranted part to be 

identical in all material respects to the part as described in the engine manufacturer’s application for 
certification for a period of two years. 

 
3. THE WARRANTY ON EMISSION-RELATED PARTS WILL BE INTERPRETED AS 
FOLLOWS: 

 

a. Any warranted part that is not scheduled for replacement as required maintenance in the 

Owners Manual shall be warranted for the ECS Warranty Period. If any such part fails during the ECS 
Warranty Period, it shall be repaired or replaced by CPE according to Subsection “d” below. Any such 
part repaired or replaced under the ECS Warranty shall be warranted for any remainder of the ECS 
Warranty Period. 

b. Any warranted, emissions-related part which is scheduled only for regular inspection as 

specified in the Owners Manual shall be warranted for the ECS Warranty Period. A statement in such 
written instructions to the effect of “repair or replace as necessary”, shall not reduce the ECS Warranty 
Period. Any such part repaired or replaced under the ECS Warranty shall be warranted for the remainder 
of the ECS Warranty Period. 

c. Any warranted, emissions-related part which is scheduled for replacement as required 

maintenance in the Owner’s Manual shall be warranted for the period of time prior to the first scheduled 
replacement point for that part. If the part fails prior to the first scheduled replacement, the part shall be 
repaired or replaced by CPE according to Subsection “d” below. Any such emissions-related part repaired 
or replaced under the ECS Warranty, shall be warranted for the remainder of the ECS Warranty Period 
prior to the first scheduled replacement point for such emissions-related part. 

d. Repair or replacement of any warranted, emissions-related part under this ECS Warranty shall 

be performed at no charge to the owner at a CPE Authorized Service Outlet. 

e. The owner shall not be charged for diagnostic labo

u

r which leads to the determination that a 

part covered by the ECS Warranty is in fact defective, provided that such diagnostic work is performed at 
a CPE Authorized Service Outlet. 

f. CPE shall be liable for damages to other original engine components or approved modifications 

proximately caused by a failure under warranty of an emission-related part covered by the ECS Warranty. 

g. Throughout the ECS Warranty Period, CPE shall maintain a supply of warranted emission-

related parts sufficient to meet the expected demand for such emission-related parts. 

h. Any CPE Authorized and approved emission-related replacement part may be used in the 

performance of any ECS Warranty maintenance or repair and will be provided without charge to the 
owner. Such use shall not reduce CPE’s warranty obligation. 

i. Unapproved add-on or modified parts may not be used to modify or repair a CPE engine. Such 

use voids this ECS Warranty and shall be sufficient grounds for disallowing an ECS Warranty claim. CPE 
shall not be liable hereunder for failures of any warranted parts of a 
CPE engine caused by the use of such an unapproved add-on or modified part. 

 

Summary of Contents for 92208





























Reviews: