background image

1

 

ENGLISH

 

92251-1

INTRODUCTION

Record the model and serial numbers as well as date and place of purchase for future reference. Have this 
information available when ordering parts and when making technical or warranty inquiries.

Champion Power Equipment Support

Model Number

Serial Number

Date of Purchase

Purchase Location

1-877-338-0999

92251-1

For 

Oil Type see ‘Add Engine Oil‘ section. For Fuel Type see ‘Add Fuel‘ section.

Congratulations on your purchase of a Champion Power Equipment product. Champion Power Equipment and 
Champion Engine Technology designs, builds, and supports all of our products to strict specifications and guidelines. 
With proper product knowledge, safe use, and regular maintenance, this product should bring years of satisfying 
service.
 
Every effort has been made to ensure the accuracy and completeness of the information in this manual, and we 
reserve the right to change, alter and/or improve the product and this document at any time without prior notice. 

Since CPE/CET highly value how our products are designed, manufactured, operated and are serviced, and also 
highly value your safety and the safety of others, we would like you to take the time to review this product manual 
and other product materials thoroughly and be fully aware and knowledgeable of the assembly, operation, dangers 
and maintenance of the product before use. Fully familiarize yourself, and make sure others who plan on operating 
the product fully familiarize themselves too, with the proper safety and operation procedures before each use. Please 
always exercise common sense and always error on the side of caution when operating the product to ensure no 
accidents, property damage, or injury occurs. We want you to continue to use and be satisfied with your CPE/CET 
product for years to come.

Summary of Contents for 92251-1
































Reviews: