background image

5

 

ENGLISH

 

92251-1

SAFETy RULES

Training

1.  Read the Operator’s Manual completely before 

attempting to use this log splitter.

2.  Do not allow anyone to operate your log splitter who 

has not read the Operator’s Manual or has not been 
instructed on the safe use of the log splitter.

3.  Never allow children or untrained adults to operate 

this machine.

4.  Many accidents occur when more than one (1) 

person operates the log splitter. If a helper is 
assisting in loading logs to be split, never actuate 
controls until helper is clear of the area.

5.  Never allow anyone to ride on the machine.
6.  Never transport cargo on the log splitter.
7.  High fluid pressures are developed in hydraulic 

log splitters. Pressurized hydraulic fluid escaping 
through a pin hole opening can puncture skin 
and cause sever blood poisoning. Therefore, the 
following instructions should be heeded at all times.
a.  Do not operate the unit with frayed, kinked, 

cracked or damaged hoses, fittings, or tubing.

b.  Stop the engine and relieve hydraulic system 

pressure before changing or adjusting fittings, 
hoses, tubing, or other system components.

c.  Do not adjust the pressure settings of the pump 

or valve.

d.  Do not check for leaks with your hand. Leaks 

can be detected by passing cardboard or wood 
over the suspected area. Look for discolouration. 
If injured by escaping fluid, see a doctor at 
once. Serious infection or reaction can develop 
if proper medical treatment is not administered 
immediately.

8.  Keep the operator zone and adjacent area clear for 

safe, secure footing.

9.  If your log splitter is equipped with an internal-

combustion engine and intended for use near any 
unimproved forest, brush, or grass covered land, 
the engine exhaust should be equipped with a spark 
arrestor. Make sure you comply with local, state, 
and federal codes. Take appropriate fire-fighting 
equipment with you.

10. Log splitters should be used only for splitting 

wood. Do not use for other purposes unless the 
manufacturer provides attachments and instructions.

Preparation

1.  Be thoroughly familiar with all controls and with 

proper use of the equipment.

2.  Safety Gear:

a.  Always wear safety shoes or heavy boots when 

operating the machine.

b.  Always wear safety glasses or goggles when 

operating the machine.

c.  Never wear jewelry or loose-fitting clothing that 

might become entangled in moving or rotating 
parts of the machine.

3.  Make sure the splitter is on a level surface. Block 

tires and ensure support leg is secure to prevent 
unintended movement of the log splitter during 
operation.
a.  Always operate the splitter from the 

manufacturer’s indicated operator zone.

4.  Logs to be split on ram-type units should be cut as 

squarely as possible.

5.  Fuel:

a.  Use an approved fuel container.
b.  Never add fuel to a running or hot engine.
c.  Fill fuel tank outdoors with extreme care. Never 

fill fuel tank indoors.

d.  Replace gasoline cap securely and clean up any 

spilled fuel.

Summary of Contents for 92251-1
































Reviews: