background image

Champion Power Equipment, Inc (CPE), 

Emission Control System Warranty 

 

Your Champion Power Equipment (CPE) engine complies with Environment Canada (EC) emission 
regulations. 
 

YOUR WARRANTY RIGHTS AND OBLIGATIONS:

 

 
CPE is pleased to explain the Emission Control Systems Warranty on your 201

4

 small off-road engine. 

New engines must be designed, built and equipped, at the time of sale, to meet EC regulations for small 
non-road engines. CPE must warrant the emission control system on your small off-road engine for the 
period of time listed below, provided there has been no abuse, neglect, unapproved modification, or 
improper maintenance of your small off-road engine. 
 
Your emission control system may include parts such as the carburetor, fuel-injection system, the ignition 
system, catalytic converter and fuel lines. Also included may be hoses, belts, connectors and other 
emission related assemblies. Where a warrantable condition exits, CPE will repair your small off-road 
engine at no cost to you including diagnosis, parts and labor. 

 
MANUFACTURER’S EMISSION CONTROL SYSTEM WARRANTY COVERAGE: 
 

This emission control system is warranted for two years, subject to provisions set forth below. If,

 

during 

the warranty period, emission related part on your engine is defective in materials or

 

workmanship, the 

part will be repaired or replaced by CPE.

 

 
OWNER WARRANTY RESPONSIBILITIES: 

 
As the small off-road engine owner, you are responsible for the performance of the required maintenance 
listed in your Owner’s Manual. CPE recommends that you retain all your receipts covering maintenance 
on your small off-road engine, but CPE cannot deny warranty solely for the lack of receipts or for your 
failure to ensure the performance of all scheduled maintenance. 

 
As the small off-road engine owner, you should however be aware that CPE may deny you 
warranty coverage if your small, off-road engine or a part has failed due to abuse, neglect, 
improper maintenance or unapproved modifications. 

 
You are responsible for presenting your small off-road engine to an Authorized CPE service outlet, CPE 
dealer or CPE, Santa Fe Springs, CA., USA as soon as a problem exists. The warranty repairs should be 
completed in a reasonable amount of time, not to exceed 30 days. 
 
If you have any questions regarding your warranty rights and responsibilities, you should contact: 
 

Champion Power Equipment, Inc. 

Customer Service 

10006 Santa Fe Springs Road 

Santa Fe Springs, CA 90670 

USA 

Tel: 1-877-338-0999 

tech@championpowerequipment.com 

 
 

Summary of Contents for 92750






























Reviews: