background image

100594 - 1600 PORTABLE POWER STATION

IMPORTANT SAFETY INSTRUCTIONS

5

Lithium-ion Battery Safety

 

DANGER

Electrolyte inside the battery is harmful to skin and eyes. 
Electrolyte may pose an increased risk of harm if not handled 
properly. 

Under abusive conditions, liquid may be ejected from the 
battery; avoid contact. Liquid ejected from the battery may 
cause irritation or burns. If contact accidentally occurs, flush 
with water. If the battery leaks and electrolyte gets in your 
eyes, do not rub them, immediately flood eye with running cold 
water for at least 10 minutes and seek medical help. If left 
untreated, electrolyte can cause permanent eye injury. Keep 
away from children.

 

DANGER

This Power Station generates the same potential lethal AC 
electrical voltage as a standard building wall outlet.

Always treat the Power Station as you would a normal AC 
outlet on a standard building wall.

 

WARNING

When using the Power Station:

 

Always use in a dry well ventilated area while in use and 
do not obstruct fan openings on unit. Inadequate ventilation 
may cause execessive heat and damage the unit.

 

Always keep the unit clean and dry and inspect for dirt, 
dust, or moisture prior to every use.

 

Power cord plugs must always match the outlet. Never 
modify the plug in any way. Do not use any adapter plugs 
with earthed (grounded) power tools.

 

Connect only to properly grounded outlets.

 

To reduce risk of damage to the electric plug and cord, 
pull the plug rather than the cord when disconnecting the 
Power Station. Never use the cord for carrying, pulling or 
unplugging the tool.

 

Do not use this Power Station if the power cord or the 
battery cables are damaged in any way.

 

Always use a suitable extension cord to reduce the risk of 
electric shock.

 

Always keep the cord away from heat, oil, sharp edges or 
moving parts.

 

Always position cords carefully to avoid hazardous 
conditions. Tripping or snagging on cords can cause 
injury or cause product damage. Never allow cords to run 
through puddles or across wet ground.

 

Use of an accessory attachment not recommended or sold 
by the Power Station manufacturer may result in a risk of 
fire, electric shock, or injury to persons.

 

To reduce the risk of electric shock always unplug the 
cord from outlet when not in use and before servicing or 
cleaning.

 

Do not insert foreign objects into outputs or ventilation 
holes.

 

WARNING

 

Do not overload the Power Station’s capacity. Exceeding 
the wattage/amperage capacity may damage the power 
supply and/or electrical devices connected to it.

 

Do not connect Power Station output to a building’s 
electrical system.

 

Do not use this unit if you do not understand these 
operating instructions.

 

Maintain the labels and nameplates on this Power Station. 
These carry important information. If unreadable or 
missing, contact our Champion Technical Support Team for 
a free replacement.

Summary of Contents for 100594






























Reviews: