background image

 

Form No. BU-62 1/19 

   Copyright © 2015 Gardner Denver, Inc

 

 

COMPRESSOR PRODUCTS 

D Series, DRS Series: 

 

3.

 

Participation in Champion’s oil analysis sampling program is required. An oil sample must be sent to our lubricant analysis laboratory every 2000 
hours or every 6 months
, whichever occurs first. Any recommendations detailed in the oil analysis report must be followed as outlined in the 
report. Oil sample bottles are to be obtained from your local authorized Gardner Denver distributor. 
 

4.

 

The use of approved Champion lubricants is required. The following lubricants are approved for warranty and must be changed in accordance with 
the above maintenance tables or a minimum of every 12 months. Oil filter and separator elements must be replaced at the time of the lubricant 
change.  

D Series, DRS Series:  
RotorLub 8000, RotorLub 8000TH, RotorLub 4000, Rotorlub 4000FG, RotorLub 4000FG-68 

 

5.

 

A log of all maintenance performed must be maintained with the corresponding operational hours. This includes the following changes: air filter, oil 
filter, separator, and lubricant. All other maintenance and repairs also require logging and documentation with corresponding hours.  

 
 
PREMIUM WARRANTY PLAN DISCLAIMER 
CHAMPION RESERVES THE RIGHT TO CHANGE THE PREMIUM WARRANTY PLAN AND/OR REQUIREMENTS AS DEEMED APPROPRIATE BY THE COMPANY. CHAMPION RESERVES THE 
RIGHT TO REFUSE PARTICIPATION IN THE PREMIUM WARRANTY PLAN TO ANY DISTRIBUTOR AND/OR END CUSTOMER OF THE COMPRESSOR. THIS PREMIUM WARRANTY PLAN IS 
SUPPLEMENTAL TO THE STANDARD WARRANTY. COMPANY MAKES NO OTHER WARRANTY OR REPRESENTATION OF ANY KIND, EITHER EXPRESS OR IMPLIED. THE FOREGOING 
WARRANTY IS EXCLUSIVE AND IT IS EXPRESSLY AGREED THAT, EXCEPT AS TO THE TITLE, COMPANY MAKES NO OTHER WARRANTIES EXPRESSED, IMPLIED, OR STATUTORY, 
INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY. THIS WARRANTY SHALL NOT BE EFFECTIVE AS TO ANY CLAIM WHICH IS NOT PRESENTED WITHIN 30 DAYS AFTER THE 
DATE UPON WHICH THE PRODUCT IS CLAIMED NOT TO HAVE BEEN AS WARRANTED. ANY ACTION FOR BREACH OF THIS WARRANTY MUST BE COMMENCED WITHIN ONE YEAR 
AFTER THE DATE UPON WHICH THE CAUSE OF ACTION OCCURRED. 
 

NO WARRANTY IS MADE WITH RESPECT TO:  
1.

 

ANY PRODUCT WHICH HAS BEEN REPAIRED OR ALTERED IN SUCH A WAY, IN THE COMPANY’S SOLE JUDGMENT, AS TO AFFECT THE PRODUCT ADVERSELY 

2.

 

ANY PRODUCT WHICH HAS, IN THE COMPANY’S SOLE JUDGMENT BEEN SUBJECT TO NEGLIGENCE, ACCIDENT, IMPROPER STORAGE, OR IMPROPER INSTALLATION OR APPLICATION 

3.

 

ANY PRODUCT WHICH HAS NOT BEEN OPERATED OR MAINTAINED IN ACCORDANCE WITH THE RECOMMENDATIONS OF THE COMPANY 

4.

 

ANY RECONDITIONED OR PRIOR OWNED PRODUCT 

 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

Component 

Change Interval 

Oil Filter 

Every 2000hrs or 6 months, whichever occurs first  

Oil Sample 

Every 2000hrs or 6 months, whichever occurs first  

Lubricant 

Change per recommendations of the Oil Analysis or hour Life rating of lubricant or 
as indicated by controller or 12 months

whichever occurs first 

Separator 

Every 4000hrs or 12months, whichever occurs first 

Inlet Air Filter 

Every 2000hrs or 6 months, whichever occurs first  

Control Box Filter 

Every 2000hrs or 6 months, whichever occurs first  

Cabinet Air Filter 

Every 2000hrs or 6 months, whichever occurs first  

 

Summary of Contents for D5









































Reviews: