Chanberlain JM60-433, Instruction Manual

Replacement Parts

(1)

41A5644

Trolley with Chain/Cable Assy.
(3 piece rail)

041A0516-1

Trolley with Chain/Cable Assy
(1 piece rail)

(2)

041A6342

Head Only

(3)

041A5643-4

Hardware Bag

(4)

41B0668

Door Bracket

(5)

41C0669

Header Bracket

(6)

001A5644

Inner Trolley

(7)

41C5620

Outer Trolley

(8)

41C0521-1

Limit Switch (3 piece rail)

041A0521-2

Limit Switch (1 piece rail)

(9)

002D0838

1 piece rail

(10)

41A5675

Rail Hardware

(11)

41A5676

Rail Sections

041A5626

Logic Board 

041A0157-1

Transformer

Specifications

Input Voltage  . . . . . . . . . .230 VAC 50/60 Hz
Max. Pull force  . . . . . . . .600N
Rated Power Input  . . . . .85 Watts
Rated Load  . . . . . . . . . . .3.0 Nm
Standby Power  . . . . . . . .9 Watts
Max. Door Weight  . . . . . .60kg

Motor

Type  . . . . . . . . . . . . . . . .63:1 Worm Gear Reduction
Volts  . . . . . . . . . . . . . . . .24VDC

Drive Mechanism

Length of Travel  . . . . . . .2.8M
Travel Rate  . . . . . . . . . . .8cm/sec
Lamp  . . . . . . . . . . . . . . . .24V 21 Watts

Safety

Electronic  . . . . . . . . . . . .Auto-Force Adjustment
Electrical  . . . . . . . . . . . . .Thermal Fuse in Transformer
Limit Adjustment  . . . . . . .Manual

Dimension

Length (Overall)  . . . . . . .3.3m
Headroom Required  . . . .30mm
Hanging Weight . . . . . . . .10kg

Receiver Code Registers

Billion Code  . . . . . . . . . . .12
Dip Switch  . . . . . . . . . . . .1
Keypad  . . . . . . . . . . . . . .1
Operating Frequency  . . .433.92MHz

24

Accessories

(1) Model

4335EML

3-Function Mini Remote Control

(2) Model

770EML

The Protector System

(3) Model 

747EML

Wireless Keyless Entry Keypad

(4) Model

845EML

Multi-Function Door Control Panel

(5) Model

75EML

Lighted Door Control Button

(6) Model

760EML

Outside Keylock

(7) Model

1702EML

Outside Quick Release

23

Wiring the Multi-Function Door Control Panel

and the Lighted Door Control Button (Optional)

Locate any Wall Mounted Door Control where the garage door
is visible, away from door and door hardware, at a minimum
height of 1.5m. fasten the child warning label on the wall near
the Door Control.

There are 2 screw terminals (1) on the back of the Door Control
(2). Strip about 6mm of insulation from bell wire (4). Separate wires
enough to connect the white/red wire to terminal screw 1 and the
white wire to terminal screw (1).

Lighted Door Control Button:

Fasten to an inside garage wall

with sheet metal screws (3) provided with Lighted Push Button.
Drill 4mm holes and use anchors (6) if installing into drywall or
concrete. A convenient place is beside the service door and 

out of

reach of children.
Multifunction Door Control: 

Insert a small flat head screwdriver

into the top of the Wall Control (10), gently pry the cover off.
Fasten to an inside garage wall with sheet metal screws (8) as
follows:
•  Install bottom screw, allowing 3mm to protrude from the wall.
•  Position bottom of door control over screw head and adjust for

snug fit. 

• Install top screw with care to avoid cracking plastic housing. 

Do

not over tighten.

• Replace cover by inserting bottom tabs (9) and snapping into

place. To remove cover after mounting, gently pry at top with
paper clip or small flat head screwdriver.

Run the bell wire up the wall and across the ceiling to the garage
door opener. Use insulated staples (5) to secure wire.
The opener Quick-Connect Terminals (7) are located in the recess
next to the learn button on the left side panel. Insert bell wire into
holes in the Quick Connect Terminals as follows: Red/White to
Red and White to White.

22

114A3269B

Printed in China

5-GB