background image

Page 4 

 

Important Safety Information 

Always read this manual before fitting or operating the machine 

 whenever any doubt exists contact your 

dealer or the Chapman Machinery Service Department for advice and assistance. 

 

 

DEFINITIONS 

The following definitions apply throughout this manual:

 

 

WARNING - 

An operating procedure, technique etc., which can result in personal injury or loss of life if not observed 

carefully. 

 

CAUTION - 

An operating procedure, technique etc., which can result in damage to either machine or equipment if 

not observed carefully.

 

 

NOTE 

- An operating procedure, technique etc, which is considered essential to emphasis.

 

 

LEFT & RIGHT HAND

 - This term is applicable to the machine when attached to the towing vehicle and is viewed from 

the rear 

 this also applies to tractor references.

 

 

Safety Information 

 

Do not operate this equipment unless you have studied this manual in full 

 

Only use this machine for its designated task - improper use is both highly dangerous and damaging to 
machine components 

 

Both operators & maintenance fitters should be familiar with the machine and fully aware of dangers 
surrounding improper use or incorrect repairs 

 

Before starting, carry out a visual check on both machine & towing vehicle as regards functionality, road 
safety & accident prevention rules 

 

Even when using the machine correctly, accidents can occur. It is imperative that nobody stand within the 
danger area. If working near roads, buildings or animals, special attention must be taken to ensure safety. 

 

Never wear loose clothing which could get caught in rotating equipment 

 

Never carry passengers on the towing vehicle 

 

Do not stand near the machine when operating 

 

Damaged or missing safety decals must be replaced immediately 

 

Transportation Safety 

 

 

When transporting, especially over rough ground, reduce speed to prevent damage to machine. 

Operating Safety 

 

 

Pay special attention when working not to harm livestock if crowding around the machine occurs. 

 

If anything should become entangled in the mechanism, or blocked in the chute, stop the machine and disconnect 
the power before attempting to clear the blockage. DO NOT REACH INTO THE MECHANISM WHEN RUNNING AS 
INJURY MAY RESULT. 

 

Ensure carrying vehicle has sufficient bed load rating to carry the weight of the  feed when full.  

Summary of Contents for MGF350















Reviews: