Insert 3/4” Carriage Bolts into bracket on Legs
Make sure all
before fastening
four
tabs are inside slots
Hinge Pin
and Hitch Pin
Items to Assemble:
1 Grill Lid
2 Hinge Pin
2 Hitch Pin
Qty: 2
Qty: 2
Qty: 2
Items to Assemble:
1 Logo Plate with clips
1 Handle
2 Wing Nuts
Wheel attaches
in BOTTOM HOLE
on legs
Tank Retainer
1st: Unfold legs. Do not stand cart up until front panel is attached. The front panel stabilizes
the cart.
Qty: 2
Qty: 1
Items to Assemble:
2 Wheels
1 Tank Support
2 Axle Bolts
2 Hitch Pins
2 Hub Caps
1 Tank Retainer
1 1-1/4” Carriage Bolt
1 Wing Nut
2 Control Knobs
1 Rotary Ignitor
Qty: 2
1-1/4” Carriage Bolt
463823303
Rotary Knob may be attached
Hub on wheel faces into leg.
Attach in bottom hole on leg
with axle bolt and hitch pin.
Qty: 7
Items to Assemble:
1 Upper Panel
4 2” Carriage Bolts
4 Wing Nuts
1 Lower Panel
3 2” Carriage Bolts
3 Wing Nuts
Lower Panel inserts into Upper Panel
Slide Upper Panel
under UFC
Stand Cart Upright
Items to Assemble:
1 Left Shelf
2 3/4” Carriage Bolts
2 Wing Nuts
2 Wing Screws
Repeat for Right Side
1 Right Shelf
2 3/4” Carriage Bolts
2 Wing Nuts
2 Wing Screws
Qty: 7
Item to Assemble:
1 Condiment Wire
1 Condiment Tray
A
Eyelet End
Match-Holder
Place end of chain through hole, reattach coupling to end of chain.
Thread eyelet on other end of chain into loop of match holder.
Remove coupling from chain
Back of Grill
Eyelet End
Match-Holder
CAUTION
!
• Failure to install can in clip will cause hot
grease to drip from bottom of grill with
risk of fire or property damage.
Items to assemble:
1 Chain with Coupling
1 Match-Holder
1 Grease Clip
Grease Clip
See Use & Care Manual for “Match Lighting Instructions”
Hang grease clip from center of grill bottom.
Use an empty soup can (not included) to hang from grease clip.
View looking down
Tank Support
Qty: 1
1st Remove styrofoam pad
Items to Assemble:
2 Tent Frames
2 Burner Tents
2 Grates
1 Griddle
1 Shield
Items to Assemble
1 Chef’s Delite
2 Swing Grid Bolts
2 Wing Nuts
Qty: 2
LP tank is shipped empty. Fill and leak check before
attaching to grill and regulator.
See Use and Care to perform the “Burner Flame Check”
and important safety instructions before using
Loosen wing-nut on tank retainer.
Center base of tank in notches between wheels.
Lower tank retainer onto tank and tighten the wing-nut.
CAUTION
!
Tank collar opening must face to front of cart once tank is
attached.
Failure to install tank correctly may allow gas hose to be
damaged in operation, resulting in the risk of fire.
•
•
Items to Assemble:
1 LP Tank
Regulator
Wing-Nut
Notch in Tank
Retainer
Facin
g
Front
Tank
Qty: 2
Qty:4
Qty:4
Qty:4
1
9
10
9
8
4
5
6
7
1
2
3
B
Griddle
Shield
Tent Frame
Burner Tent
Grates
