background image

 

 

 

LT8019 

SECTION THREE Cleaning (Users Instructions) 

Warning: -  

Before you clean any part of the appliance ensures that the appliance is turned off and cold. 

 

Cleaning: Black Painted Surfaces 

The outer body simply needs to be dusted or wiped with a clean cloth from time to time. DO NOT use wet cloths as it 
can spread plaster, cement, fire cement or fire board dust and subsequently cause the paint to turn grey with heat 
where it has been wiped. DO NOT use any kind of furniture polish or cleaning agent other than your stove suppliers 
recommended paint. All painted stoves will require some re-painting from time to time. The stove can simply be re-
painted by using high temperature stove spray paint after rubbing down with wire wool or similar abrasive to 
remove all loose debris from the surfaces.  

Stove paint finishes will require touching up or re-painting from time to time and failure to maintain the surface 
finish can lead to unnecessary corrosion. Looking after the paint finish is normal maintenance and not covered by 
warranty. 

 

Glass Cleaning 

From time to time it will be necessary to clean the glass panel of your Edge BF Gas Stove. We recommend you use a 
Ceramic hob cleaner these are available for all leading super markets: - i.e. 

ASDA, TESCO, SAINSBURY’S

 Etc. 

Brands of hob cleaning we have tested and found suitable are - 

HOB BRITE & VITRO CLEAN.  

 

Ensure the fire as been turned OFF for at least four hours to ensure it is cool.

 

 

Pull forward on the door to disengage the lower magnets and lift the door upwards to remove.

 

 

Loosen the lower 3 M4 fixing nuts but do not remove.

 

 

Remove the 9 off M4 fixing nuts from the glass fixing brackets located at the top and sides of the glass panel.

 

 

Remove the top and side fixing brackets while supporting the glass panel.

 

 

Lift the glass panel from within the bottom support bracket. 

 

 

Follow the instructions on the Hob Cleaner Bottle.

 

 

On stubborn stains (where the appliance as been used for a long period without glass panel being cleaned), 
use a new Brillo Pad well wetted with the Hob cleaner applied directly to it.

 

 

Ensure all residue of the cleaner is removed with a damp cloth and the glass panel is completely dry before 
refitting the glass.

 

Important: - The appliance must not be used if the glass panel is missing or damaged. 

Note: - The glass may discolour quickly when first installed, and it should be cleaned.  This is due to the burning off 
process of the refractory shapes. 

 

 

 

 

 

 

 

 

Summary of Contents for Edge 3s BF









































Reviews: