Charnwood BD48 Owner'S Manual Download | Manualshive

Page: 8 / 16

background image

The port is 64mm/57mm
external/internal diameter.

Setting Up

Tracking the belt

Ensure the machine is disconnected
Slowly rotate the belt by hand by
turning the sanding disc, ensuring that
it is travelling in the direction of the
arrow.

Note if the belt is tending to slide off
the bed and to which side.

If the belt doesn’t slide sideways it is
already correctly tracked.

Viewed from the switch end, if the belt
moves sideways towards the disc:
Turn the tracking knob clockwise
(1/4 turn is usually sufficient).

If the belt moves sideways away from
the disc:
Turn the knob ant-clockwise.

Continue adjustments until the belt
remains central on the rollers.

Tracking Knob

«
...
6
7
8
9
10
...
»

Summary of Contents for BD48

















Reviews:

No comments

Related manuals for BD48

Brand: ulsonix Pages: 218

Brand: MIRKA Pages: 104

Brand: Jet Pages: 36

ULTRAMAX UM-1200

Brand: Gesswein Pages: 2

Brand: Ratio Pages: 48

Brand: Grizzly Pages: 48

Brand: Milwaukee Pages: 31

Brand: Parkside Pages: 76

Brand: Skil Pages: 100

Neji Taro III HS III-10

Brand: HIOS Pages: 28

Brand: Worx Pages: 120

Brand: Wen Pages: 20

Brand: Hyper Tough Pages: 12

Brand: TriStar Pages: 16

Brand: Landis Pages: 13

Brand: M7 Pages: 60

Brand: Power Fist Pages: 16

Brand: Pallmann Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands