background image

 

6

SPECIAL SAFETY INSTRUCTIONS FOR LOG SPLITTER 

 
1.  The log splitter must always be used by one operator only. 
2.  Nobody must be allowed to use the log splitter unless they have read the instruction manual 

and have been instructed in the regulations to follow for correct and safe use. 
Operators must receive necessary training and instructions. 

3.  The machine must be used by adults only. Use of the log splitter by apprentices of not less 

than 16 years of age must be supervised by an adult authorized to use the machine. 

4.  Never wear loose, unbuttoned clothing which may become trapped in moving parts. 
5.  Position the machine on a support surface of 60-75 cm height, free from any objects that could 

prevent complete freedom of movement for the operator while working. The surface must be 
perfectly leveled to prevent the machine from falling during operation. 

6.  It is prohibited to work with the machine on the ground. This is not only an uncomfortable 

working position but it can also be dangerous because the operator has to bring his face close 
to the machine, and thus risks being struck by chips or debris. 

7.  Check that the logs to be split are free from nails or wire, which may fly up or damage the 

machine, the ends of the logs must be cut square, branches must be cut off flush with the 
trunk. 

8.  Never try to split logs larger than those indicated in the technical specifications. This could be 

dangerous and may damage the machine. 

9.  Break wood in the direction of the grain, do not place wood across the log splitter and leave it 

in that position for splitting; it may be dangerous and may seriously damage the machine. 

10.  Never attempt to cut two logs at once, one may fly up and hit you. 
11.  If the log moves away from the blade, retract the ram or the blade and turn the log through 90

0

12.  Do not attempt to load the log in the log splitter while the ram is in motion, you could get 

trapped and injured. 

13.  Keep your hands well away from any splits and cracks which open in the log; these may close 

suddenly and crush or amputate your fingers. 

14.  Never force the log splitter for more than 5 seconds keeping the cylinder under pressure in the 

attempt to split excessively hard wood. After this time interval, the oil under pressure is 
overheated and the machine could be damaged. It is thus better to stop and rotate the log by 
90

0

 to see whether it can be split in a different position. In any case, if you are not able to split 

the log, this means that its hardness exceeds the capacity of the machine and thus that log 
should be discarded so as not to damage the lop splitter. 

15.  Do not force the blade by pushing the log on the upper part, as this can cause the blade to 

break or damage the body of the machine. Always set the log on the guides. 

16.  Never leave the machine unattended while it is running. If you leave the machine, even for a 

short time, remove the power supply or any possible cause of accidental start-up. 

17.  The log splitter must never be used by an operator who is under the influence of alcohol, drugs, 

medicines, or who is tired. A clear mind is essential for safety. 

18.  Never request the assistance of another person to help you remove a jammed log. 
19.  Do not use machines with electric motor if natural gas, petrol fumes or other inflammable 

vapours are present. 

Summary of Contents for LS5T37A


















Reviews: