background image

 

 

R-NET 

www.chasswheel.com  

rev. 1 

2014-05-08

 

 

32

 

7 WHEELCHAIR STORAGE 

 
Protect the wheelchair from heat and moisture during storage. The wheelchair goes into the smaller 

space by folding the back rest, the arm rests and the foot rest. 

 

Disconnect the batteries and store them fully recharged in a dry and cool place. During the storage 

the batteries should be recharged at least once every six months. 

Use of the wheelchair as a seat in a vehicle

 

 

In order to use a wheelchair as a motor vehicle seat, it needs to be equipped with attachment points 

to enable anchoring in the motor vehicle. These accessories may be included in the standard scope 

of wheelchair order but may also be obtained from Chasswheel as an option. 

 

This power wheelchair complies with the requirements of ISO 7176-19:2001 and may be used as a 

vehicle  seat  in  connection  with  an  anchoring  system  that  has  been  checked  and  approved  in 

accordance with ISO 10542. The wheelchair has undergone a crash test in which it was anchored in 

the  transporting  vehicle's  direction  of  travel.  Other  configurations  were  not  tested.  The  crash  test 

dummy was secured using pelvic and upper body safety belts. Both types of safety belt should be 

used  in  order  to  minimize  the  risk  of  injuries  to  head  or  upper  body.  It  is  imperative  that  the 

wheelchair is inspected by  an  authorized  dealer before  being  used  again  after being involved in  a 

crash.  Alterations  to  the  wheelchair  anchoring  points  may  not  be  carried  out  without  the 

manufacturer's permission.  

 

Caution: There is a danger of injury if the wheelchair is not properly secured during use 

as a vehicle seat!  

 
• If possible, the user should always leave the wheelchair to use a vehicle seat and the safety belts 

provided with the vehicle.  

 

• The wheelchair should always be anchored facing in the transport vehicle's intended direction of 

travel. 

 

• The wheelchair must always be secured in accordance with the wheelchair and anchoring system 

manufacturers’ operating manual.  

 

• Always remove and secure any accessory parts fixed to the wheelchair such as chin controls or 

tables.  

 

• If your wheelchair is equipped with an angle adjustable backrest, then it must be placed in an 
upright position.  

 

• Fully lower elevated leg rests, if fitted. 

 

• Fully lower the seat lifter, if fitted.  

 

• Always completely lower height-adjustable leg rests, if fitted 

WARNING: Danger of injury exists if a power wheelchair that is not equipped with leak-

proof batteries is transported in a vehicle!  

Summary of Contents for Four X DL




















































Reviews: