Chatsworth Products GlobalFrame GF Series User Manual Download

Page: 29 / 30

Thermal Management (cont’d)

Air Dam, 6-‐Slide Cabinet

42U x 600 -‐

39085-‐X00

For 23.6” (600 mm), 27.6” (700 mm),

45U x 600 -‐

39085-‐X03

29.5” (750 mm) and 31.5” (800 mm)

48U x 600 -‐

39085-‐X06

wide cabinets

52U x 600 -‐

39085-‐X10

Use with Bottom Panel, p.28, and

42U x 700 -‐

39085-‐X11

Snap-‐In Filler Panel, p.29.

45U x 700 -‐

39085-‐X14

48U x 700 -‐

39085-‐X17

52U x 700 -‐

39085-‐X21

42U x 750 -‐

39085-‐X33

45U x 750 -‐

39085-‐X36

48U x 750 -‐

39085-‐X39

42U x 800 -‐

39085-‐X22

45U x 800 -‐

39085-‐X25

48U x 800 -‐

39085-‐X28

52U x 800 -‐

39085-‐X32

Air Dam, 4-‐Slide Cabinet

42U x 600 -‐

39130-‐X00

For 23.6” (600 mm), 27.6” (700 mm),

45U x 600 -‐

39130-‐X03

and 31.5” (800 mm) wide cabinets

48U x 600 -‐

39130-‐X06

Use with Bottom Panel, p.28, and

52U x 600 -‐

39130–X10

Snap-‐In Filler Panel, p.29.

42U x 700 -‐

39130-‐X11

45U x 700 -‐

39130-‐X14

48U x 700 -‐

39130-‐X17

52U x 700

-‐ 39130-‐X21

42U x 800 -‐

39130-‐X22

45U x 800 -‐

39130-‐X25

48U x 800 -‐

39130-‐X28

52U x 800

-‐ 39130-‐X32

Baying Seal Kit

42U -‐

39137-‐700

Seals space between cabinets

45U -‐

39137-‐703

when bayed 24” apart

48U -‐

39137-‐706

52U -‐

39137-‐710

X = Color (C=Black, E=Glacier White)

Summary of Contents for GlobalFrame GF Series































Search results

Summary of Contents for GlobalFrame GF Series

Reviews:

Related manuals for GlobalFrame GF Series

Brands by name

Popular brands

Chatsworth Products GlobalFrame GF Series, User Manual

Search results

Summary of Contents for GlobalFrame GF Series

Reviews:

Related manuals for GlobalFrame GF Series

Brands by name

Popular brands