EN
2
Maverick Storm 2 BeamWash QRG Rev. 2
QUICK REFERENCE GUIDE
What is Included
AC Power
This product has an auto-ranging power supply that can work with an input voltage range of 100–240 VAC, 50/60 Hz.
AC Plug
Replacing the Fuse
1. Disconnect the product from power.
2. Using a Phillips-head screwdriver, unscrew the fuse holder cap from the housing.
3. Remove blown fuse and replace with a good fuse of the same type and rating.
4. Screw the fuse holder cap back in place and reconnect power.
Signal Connections
You can link the Maverick Storm 2 BeamWash to a controller or controller software using a DMX connection, an Ethernet
connection, or both. If using other Art-Net™, sACN, or Kling-Net-compatible products with the
Maverick Storm 2 BeamWash, you can control each individually on a single network. See the User Manual for information
about how to connect and configure the product for these signals.
Control Personalities
The Maverick Storm 2 BeamWash
uses
DMX, Art-Net™, sACN, Kling-Net, and WDMX for its control personalities:
DMX Connection
The Maverick Storm 2 BeamWash will work with a DMX controller using a 5-pin DMX serial connection or a wireless DMX
connection. A DMX Primer is available from
.
Art-Net™ Connection
Art-Net™ is an Ethernet protocol that uses TCP/IP which transfers a large amount of DMX512 data using an Neutrik®
etherCON® RJ45 connection over a large network. An Art-Net™ protocol document is available from
. Chauvet Professional recommends using unicast Art-Net™ for best results.
Art-Net™ designed by and copyright Artistic Licence Holdings Ltd.
sACN Connection
Also known as ANSI E1.31, Streaming-ACN is an Ethernet protocol that uses the layering and formatting of Architecture
for Control Networks to transport DMX512 data over IP or any other ACN compatible network.
Kling-Net Connection
Kling-Net is a network protocol that allows auto configuration of display devices using an ethernet connection. Refer to
the ArKaos software manual for detailed instructions on programming this product.
RDM (Remote Device Management)
Remote Device Management, or RDM, is a standard for allowing DMX-enabled devices to communicate bi-directionally
along existing DMX cabling. Check the DMX controller’s User Manual or with the manufacturer as not all DMX controllers
have this capability. The Maverick Storm 2 BeamWash supports RDM protocol that allows feedback to make changes to
menu map options. Download the User Manual from
for more details.
•
Maverick Storm 2 BeamWash
•
Seetronic Powerkon IP65 to bare wire power cord
•
2 Omega Brackets with mounting hardware
•
Quick Reference Guide
Connection
Wire (U.S.)
Wire (Europe)
Screw Color
AC Live
Black
Brown
Yellow/Brass
AC Neutral
White
Blue
Silver
AC Ground
Green/Yellow
Green/Yellow
Green
To eliminate unnecessary wear and improve its lifespan, during periods of non-use completely
disconnect the product from power via breaker or by unplugging it.
Single Control
Dual Control Movement
Dual Control Pixels
Basic
(31-channel)
Basic
(11-channel)
Basic
(93-channel)
Standard
(143-channel)
Standard
(34-channel)
Standard
(112-channel)
Advanced
(263-channel)
Advanced
(45-channel)
Advanced
(224-channel)
Tour
(325-channel)
Basic2
(37-channel)
In Dual Control mode, the Movement protocol and the Pixels protocol cannot be the same.
For smooth-running operation, ArKaos Kling-Net requires a gigabit (1000 Mbps) Ethernet card and
network router.
ArKaos Kling-Net will only run Standard Pixels or Basic Pixels mode.
!