background image

 

Hurricane™ 1300 User Manual 

August 2011 

 

Safety Instructions 

 

Please read the following notes carefully because they include important safety 
information about the installation, usage, and maintenance of this product. 

 

 

Please keep this User Guide for future consultation. If you sell the unit to another 
user, be sure that they also receive this instruction booklet. 

 

Always make sure that you are connecting to the proper voltage, and that the line 
voltage you are connecting to is not higher than that stated on the decal or rear panel 
of the fixture. 

 

This product is intended for indoor use only! (If applicable) 

 

To prevent risk of fire or shock, do not expose fixture to rain or moisture. Make sure 
there are no flammable materials close to the unit while operating. 

 

The unit must be installed in a location with adequate ventilation, at least 20in (50cm) 
from adjacent surfaces. Be sure that no ventilation slots are blocked. 

 

Always disconnect from power source before servicing or replacing lamp or fuse and 
be sure to replace with same lamp source. 

 

Secure fixture to fastening device using a safety chain. Never carry the fixture solely 
by its head. Use its carrying handles. 

 

Maximum ambient temperature (Ta) is 104°F (40°C). Do not operate fixture at 
temperatures higher than this.  

 

In the event of a serious operating problem, stop using the unit immediately. Never try 
to repair the unit by yourself. Repairs carried out by unskilled people can lead to 
damage or malfunction. Please contact the nearest authorized technical assistance 
center. Always use the same type spare parts. 

 

Never connect the device to a dimmer pack. 

 

Make sure the power cord is never crimped or damaged. 

 

Never disconnect the power cord by pulling or tugging on the cord. 

 

Avoid direct eye exposure to the light source while it is on.  

 
 

There are no user serviceable parts inside the unit. Do not open the housing or 
attempt any repairs yourself. In the unlikely event your unit may require service, 
please contact CHAUVET at: 954-929-1115. 

 

 

 

FCQ (Fog Cleaner Quart) was specifically developed by Chauvet to clean your 
Hurricane™ 1300. Make sure you use FCQ regularly to increase the life of your fogger. 

 

Summary of Contents for Hurricane 1300















Reviews: