background image

 
 
 
 

Intimidator™ Scan LED 200 User Manual (Rev. 02a) 

Page 11 of 22 

DMX Operation 

 

 

 

Set this product in DMX mode to control it with a DMX controller.  

1)  Connect this product to a suitable power outlet. 

2)  Turn this product on. 

3)  Connect a DMX cable from the DMX output of the DMX controller to the DMX 

input socket of this product. 

 

 

Starting Address 

 

 

 

When selecting a starting DMX address, always consider the number of DMX 
channels the selected DMX mode uses. If you choose a starting address that is too 
high, you could restrict the access to some of the fixture’s channels. 

The Intimidator™ Scan LED 200 uses up to 8 DMX channels in its 8-channel DMX 
mode, which defines the highest configurable address to 505.  

If you are not familiar with the DMX protocol, you may refer to the “DMX Primer” 
section in the 

“Technical Information”

 chapter. 

To select the starting address, do the following: 

1)  Press 

<MODE/ESC>

 until 

d***

 appears on the LED screen. 

2)  Using 

<UP>

 and 

<DOWN>

, select the starting address (

001~512

). 

3)  Press 

<ENTER>

4)  Press 

<MODE/ESC>

 until one of the DMX personalities appears on the LED 

screen (

8-CH

5-CH

). 

5)  Using 

<UP>

 and 

<DOWN>

, select the desired DMX personality. 

6)  Press 

<ENTER>

 

 

 

Only connect 32 fixtures to a single DMX daisy chain! 

 

 

 

 

Summary of Contents for INTIMIDATOR 200























Reviews: