17
Net-X II User Manual Rev. 3
Operation
Resend 2 Net-U
The Net-X II can broadcast the merged universe from the above 2 settings back onto the network. This
new merged universe can be accessed from another DMX output port on the Net-X II, or on another device
on the network (including a lighting fixture accepting ArtNet/sACN). This setting determines which universe
to rebroadcast onto the network.
1.
Select the DMX port to configure as instructed in
Set DMX Port
.
2.
Use the knob to select
9. Resend 2 Net-U
(option will only display if DMX Status is set to
OUTPUT & DMX Mode is set to HTP or LTP).
3.
Press the knob.
4.
Use the knob to select from range options (differs based on Disp Type and Protocol selections):
•
000–255
: When Disp Type is set to DEC & Protocol is set to ArtNet.
•
001–256
: When Disp Type is set to DEC & Protocol is set to sACN.
•
00H–7FH
: When Disp Type is set to HEX & Protocol is set to ArtNet.
•
01H–80H
: When Disp Type is set to HEX & Protocol is set to sACN.
5.
Press the knob.
If merging the same universe from 2 different controllers, and DO NOT want to rebroadcast this
universe back to the network, set the 1st universe, 2nd universe, and Resend universe to the
same value.
LCD Backlight
To set the amount of time after inactivity before the display backlight turns off, follow the instructions below:
1.
Use the knob to select
7. LCD Backlight
.
2.
Press the knob.
3.
Use the knob to select from the following options,
1. On
(does not turn off),
2. 10 Seconds
(turns
off after 10 seconds of inactivity),
3. 30 Seconds
(turns off after 30 seconds of inactivity), or
4.
Exit
(to cancel).
4.
Press the knob.
User Preset
This option saves 4 different preset menu option configurations. To set these presets, follow the
instructions below:
1.
Use the knob to select
8.User Preset
.
2.
Press the knob.
3.
Use the knob to select one of the four following presets:
•
1. Art-net 8-port DMX
(Sets all 8 ports to receive 8 universes of Art-Net™ from 0–7).
•
2. sACN to 8-port DMX
(Sets all 8 ports to receive 8 universes of sACN from 1–8).
•
3. 1x8 DMX Splitter
(Sets the product to operate as a DMX splitter with all 8 outputs
receiving DMX from input A).
•
4. 2x4 DMX Splitter
(Sets
1–4
outputs to
input-port A
and the
5–8
outputs to
input-port B
).
•
5. Exit
(to cancel).
4.
Press the knob.
Factory Reset
To restore the Net-X II to factory default settings, do the follow:
1.
Use the knob to select
9. Factory Reset.
2.
Press the knob.
3.
Use the knob to select
NO
(do not reset) or
YES
(reset to factory settings).
4.
Press the knob.
This will erase any existing recorded scenes.
Record Scenes
The Net-X II has the capability to record up to 10 scenes. To record scenes, follow the instructions below:
1.
Use the knob to select
10. Record Scenes
.
2.
Press the knob.
3.
Use the knob to select from
Scene 1–10
.
4.
Press the knob.
Summary of Contents for NET-XII
Page 1: ...User Manual Version V1 6 ...
