background image

Safety Instructions 

Please read these instructions carefully, which includes important 
information about the installation, usage and maintenance of this 
product.

x

 

Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that 
they also receive this instruction booklet. 

x

 

Always make sure that you are connecting to the proper voltage, and that the line voltage you are 
connecting to is not higher than that stated on the decal or rear panel of the fixture. 

x

 

This product is intended for indoor use only! 

x

 

To prevent risk of fire or shock, do not expose fixture to rain or moisture. Make sure there are no 
flammable materials close to the unit while operating. 

x

 

The unit must be installed in a location with adequate ventilation, at least 20 inches (50cm) from 
adjacent surfaces. Be sure that no ventilation slots are blocked. 

x

 

Always disconnect from power source before servicing or replacing lamp or fuse and be sure to 
replace with same lamp source. 

x

 

Secure fixture to fastening device using a safety chain. Never carry the fixture solely by its head. Use 
its carrying handles. 

x

 

Maximum ambient temperature (Ta) is 95°F (35°C). Do not operate fixture at temperatures higher 
than this.

x

 

In the event of a serious operating problem, stop using the unit immediately. Never try to repair the 
unit by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please 
contact the nearest authorized technical assistance center. Always use the same type spare parts. 

x

 

Don’t connect the device to a dimmer pack. 

x

 

Make sure the power cord is never crimped or damaged. 

x

 

Avoid direct eye exposure to the lamp while it is on.  

Caution! 

There are no user serviceable parts inside the unit. Do not open the housing or 
attempt any repairs yourself. In the unlikely event your unit may require service, 
please contact CHAUVET. 

Duty Cycle 

This fixture has a 15/15 duty cycle, meaning it can be run for fifteen minutes, and then must be left off 

for 15 minutes before it is turned on again. 

SX Mix Manual 

4

2006-12-11/15:22

Summary of Contents for SX Mix











Reviews: