58
b) MiniFlex
®
MA193, MA194 and MA196
MiniFlex
®
MA193 and MA196
Nominal range
100 / 400 / 2,000 A
ac
Measurement range
200 mA to 2,400 A
ac
Maximum clamping diameter
Length = 250 mm; Ø = 70 mm (MA 193 only)
Length = 350 mm; Ø = 100 mm
Influence of the position of the
conductor in the sensor
≤
1.5% typical, 2.5% maximum
Influence of an adjacent conductor
carrying an AC current
> 40 dB typical at 50/60 Hz for a conductor touching the sensor and
> 33 dB near the snap
Safety
IEC 61010-2-032, degree of pollution 2, 600V CAT IV, 1,000V CAT III
Table 11
Remark:
Currents < 0.05 % of the nominal range will be set to zero.
The
nominal ranges are reduced to 50/200/1,000/5,000 A
ac
at 400 Hz.
MiniFlex
®
MA194
Nominal range
100 / 400 / 2 000 / 10 000A
ac
(for the 1000 mm model)
Measurement range
50 mA to 2,400 A
ac
Maximum clamping diameter
Length = 250 mm; Ø = 70 mm
Length = 350 mm; Ø = 100 mm
Length = 1 000 mm, Ø = 320 mm
Influence of the position of the
conductor in the sensor
≤
2,5 %
Influence of an adjacent conductor
carrying an AC current
> 40 dB typical at 50/60 Hz for a conductor touching the sensor and
> 33 dB near the snap
Safety
IEC 61010-2-032, degree of pollution 2, 600V CAT IV, 1,000V CAT III
Table 12
Remark:
Currents < 0.05 % of the nominal range will be set to zero.
The
nominal ranges are reduced to 50/200/1,000/5,000 A
ac
at 400Hz.
The 10,000A range operates provided that the conductor can be clamped in the MiniFlex
®
sensor.
c) PAC93 clamp
Remark:
The power calculations are set to zero while the current zero is adjusted.
PAC93 clamp
Nominal range
1,000 A
ac
, 1,300 A
dc
93
Measurement range
1 to 1,000 A
ac
, 1 to 1,300 A
peak ac+dc
Maximum clamping diameter
One 42mm conductor or two 25.4mm conductors, or two 50 x
5mm bus bars
Influence of the position of the con
-
ductor in the clamp
> 40 dB typical at 50/60 Hz
Influence of an adjacent conductor
carrying an AC current
> 40 dB at 50/60Hz
Safety
IEC 61010-2-032, degree of pollution 2, 300 V CAT IV, 600 V CAT III
Table 13
Remark:
Currents < 1 A
ac
/
dc
will be set to zero in AC networks.
Summary of Contents for PEL 106
