background image

                                                                                                                                          Matters Need Attention 

 

 

 

ALPHAAIR 450 USER MANUAL

 

| 2021-03

 

 

P a g e  |  19

 

9.3 

Using Tips

 

 

The equipment should be handled gently during use to avoid soiling and scratching its 
surface, and it is strictly forbidden for surveyors or others sit on the container.

 

 

After the external test or operation, the surface of equipment should be cleaned regularly 
by provided clean suits (3-5 days), and check whether the structural screws and plugs are 
loose, and whether the peripheral cables are loose.

 

 

After long time storage in store, it needs to be taken out regularly (about one month) for 
power-on test to check whether the function is normal.

 

 

The  limitation of environment  temperature  is  between  –20° C to +50° C, the  humidity 
limitation is <80% RH and no condensation.

 

 

During the assembly and testing phases, the equipment should be placed on a cabinet or 
a special shelf and covered with a dustproof cloth. The laser head should be protected 
with a dustproof cover.

 

 

If the equipment is disassembled or loosen, it should be re-calibrated.

 

 

When it is difficult to rotate any rotating parts of the equipment, please do not forcibly 
rotate.  After  the  equipment  is  damaged,  please  do  not  continue  using,  otherwise  the 
damage of the equipment will increase. Do not disassemble equipment in field.

 

 

If faced rain or snow in field during work, please move the equipment into the container 
quickly. Do not work in the cold environment with low temperature in winter, in case to 
prevent condensation of water vapor on the optical lens and inside the instrument.

 

 

The single camera memory card cannot be formatted, and the internal folders cannot be 
deleted except photos, otherwise there will be a phenomenon that the photos cannot be 
taken.

 

 

9.4 

Storage Tips

 

 

When the equipment is not using, the battery must be removed and handled gently to 
avoid bumps. The battery cannot be inverted.

 

 

The equipment should be placed at a dry area in store. Try to avoid long-term stacking 
and placing

 

 

The room where the equipment is stored should be clean, dry, bright, and well ventilated. 
It  should  be  placed  flat  or  upright,  and  it  should  not  be  leaned  casually  to  prevent 
distortion.

 

 

 

Summary of Contents for AlphaAir 450





















Reviews: