Chevrolet 5.7L Corvette 2004 Shop Manual Download

Page: 309 / 1000

1. Lubricate the outer edge of the oil seal (1) with clean engine oil.

2. Lubricate the front cover oil seal bore with clean engine oil.

Fig. 193: J 41478 & Crankshaft Front Oil Seal

Courtesy of GENERAL MOTORS CORP.

3. Install the crankshaft front oil seal onto the

J 41478

guide.

4. Install the

J 41478

threaded rod (with nut, washer, guide, and oil seal) into the end of the crankshaft.

5. Use the

J 41478

in order to install the oil seal into the cover bore.

1. Use a wrench and hold the hex on the installer tool.

2. Use a second wrench and rotate the installer nut clockwise until the seal bottoms in the cover bore.

2004 Chevrolet Corvette

2004 ENGINE PERFORMANCE Engine Mechanical (Repair Instructions 1 Of 3) - 5.7L - Corvette

Helpmelearn

December-24-07 10:58:41 AM

Page 209

Summary of Contents for 5.7L Corvette 2004









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 5.7L Corvette 2004

Reviews:

Related manuals for 5.7L Corvette 2004

Brands by name

Popular brands

Chevrolet 5.7L Corvette 2004, Shop Manual

Search results

Summary of Contents for 5.7L Corvette 2004

Reviews:

Related manuals for 5.7L Corvette 2004

Brands by name

Popular brands