Chevrolet 5.7L Corvette 2004 Shop Manual Download

Page: 50 / 1000

ENGINE WILL NOT CRANK - CRANKSHAFT WILL NOT ROTATE

Engine Will Not Crank - Crankshaft Will Not Rotate

Detonation or spark knock

Verify the correct operation of the ignition controls. Refer to

Detonation/Spark Knock

in Engine Controls - 5.7L.

Loose torque converter bolts

Inspect the torque converter bolts and flywheel.

Repair as required.

Cracked flywheel - automatic
transmission

Inspect the flywheel bolts and flywheel.

Repair as required.

Excessive connecting rod
bearing clearance

Inspect the following components, and repair as required:

The connecting rod bearings

The connecting rods

The crankshaft

Excessive crankshaft bearing
clearance

Inspect the following components, and repair as required:

The crankshaft bearings

The crankshaft journals

The cylinder block crankshaft bearing bore

Cause

Correction

Seized accessory drive system
component

1. Remove the accessory drive belts.

2. Confirm that the engine will rotate. Rotate the crankshaft by

hand at the crankshaft balancer or flywheel location.

3. Repair or replace the components as required.

Seized driveline/propshaft assembly
- Corvette automatic transmission
application

1. Separate the engine flywheel from the input shaft of the

propshaft.

2. Confirm that the engine will rotate. Rotate the crankshaft by

hand at the crankshaft balancer or flywheel location.

3. Repair or replace the components as required.

Seized automatic transmission
torque converter

1. Remove the torque converter-to-flywheel bolts.

2. Confirm that the engine will rotate. Rotate the crankshaft by

hand at the crankshaft balancer or flywheel location.

3. Repair or replace the components as required.

Seized manual transmission

1. Disengage the clutch by depressing the clutch pedal.

2. Confirm that the engine will rotate. Rotate the crankshaft by

hand at the crankshaft balancer or flywheel location.

Refer to Transmission/Transaxle Unit Repair Manual.

Broken timing chain

2004 Chevrolet Corvette

2004 ENGINE PERFORMANCE Engine Mechanical (Introduction) - 5.7L - Corvette

Helpmelearn

December-24-07 10:50:09 AM

Page 50

Summary of Contents for 5.7L Corvette 2004









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 5.7L Corvette 2004

Reviews:

Related manuals for 5.7L Corvette 2004

Brands by name

Popular brands

Chevrolet 5.7L Corvette 2004, Shop Manual

Search results

Summary of Contents for 5.7L Corvette 2004

Reviews:

Related manuals for 5.7L Corvette 2004

Brands by name

Popular brands