Chevrolet 5.7L Corvette 2004 Shop Manual Download | Manualshive

Page: 65 / 1000

background image

tensioner(s) from operating properly. Also if the incorrect length drive belt(s) was installed, it may not be
routed correctly and may be turning an accessory drive component in the incorrect direction.

7:

Misalignment of the accessory drive pulley(s) may be caused from improper mounting or incorrect

installation of a accessory drive component, or the pulley is bent inward or outward from a previous
repair. Test for a misaligned pulley using a straight edge in the pulley grooves across two or three pulleys.
If a misaligned pulley is found, refer to that accessory drive component for the proper removal and
installation procedure for that pulley.

8:

Inspect the accessory drive pulley(s) to verify that they are the correct diameter or width. Using a

known good vehicle, compare the pulley sizes.

Drive Belt Squeal Diagnosis

Step

Action

Yes

No

DEFINITION: The following items are indications of drive belt squeal:

z

A loud screeching noise that is caused by a slipping drive belt(s) (this is unusual for a drive belt
with multiple ribs)

z

The noise occurs when a heavy load is applied to the drive belt(s), such as an A/C compressor
engagement, snapping the throttle, or slipping on a seized pulley, or a faulty accessory drive
component.

NOTE:

Refer to Belt Dressing Notice in Cautions and Notices.

1

Did you review the Symptoms - Engine
Mechanical diagnostic information, and
perform the necessary inspections?

Go to

Step 2

Go to

Symptoms -

Engine

Mechanical

2

Verify that there is a squealing noise.
Does the engine make the squeal noise?

Go to

Step 3

Go to Diagnostic

Aids

3

1. Remove the drive belt(s). Refer

to

Drive Belt Replacement -

Accessory

or

Drive Belt

Replacement - Air
Conditioning

.

2. Operate the engine for no longer

than 30 to 40 seconds.

Does the squealing noise still exist?

Go to

Engine Noise on Start-Up, but

Only Lasting a Few Seconds

,

Upper

Engine Noise, Regardless of Engine

Speed

, or

Lower Engine Noise,

Regardless of Engine Speed

Go to

Step 4

4

Inspect for a seized accessory drive
component bearing or a faulty
accessory drive component.
Did you find and correct the condition?

Go to

Step 9

Go to

Step 5

5

Inspect the drive belt tensioner for
proper operation. Refer to

Drive Belt

Tensioner Diagnosis

.

2004 Chevrolet Corvette

2004 ENGINE PERFORMANCE Engine Mechanical (Introduction) - 5.7L - Corvette

Helpmelearn

December-24-07 10:50:09 AM

Page 65

© 2005 Mitchell Repair Information Company, LLC.

«
...
63
64
65
66
67
...
»

Summary of Contents for 5.7L Corvette 2004









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 5.7L Corvette 2004

Brand: EBARA Pages: 36

PneuTorque PTS-52-500

Brand: norbar Pages: 30

Brand: Briggs & Stratton Pages: 14

MAX-15CV-R Series

Brand: O.S. engine Pages: 34

Brand: O.S. engine Pages: 34

Brand: O.S. engine Pages: 40

Brand: Tanaka Pages: 7

ROLLOPOWER PLUS Series

Brand: Schellenberg Pages: 120

Brand: Volvo Penta Pages: 41

Kohler KDI 1903TCR-MP

Brand: LOMBARDINI MARINE Pages: 56

RolloTube S-line DuoFern

Brand: RADEMACHER Pages: 8

RolloTube Basis

Brand: RADEMACHER Pages: 60

Brand: RADEMACHER Pages: 64

Brand: CAME Pages: 44

Brand: CAME Pages: 96

Brand: Dertec Pages: 2

Brand: LONCIN Pages: 64

Brand: Farymann Diesel Pages: 137

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands