Chevrolet 5.7L Corvette 2004 Shop Manual Download

Page: 696 / 1000

6. Tighten the expander assembly (15) nut until snug.

7. Push the guide cone (1) into the front camshaft bearing to align the tool.

Fig. 169: Bearing & Block Bore

Courtesy of GENERAL MOTORS CORP.

8. Drive the bearing from the block bore.

9. Repeat the above procedures to remove the remaining bearings.

Tool Usage Information

IMPORTANT: To remove the front camshaft bearing, operate the tool from the rear of

the block using the guide cone in the rear camshaft bearing bore.

2004 Chevrolet Corvette

2004 ENGINE PERFORMANCE Engine Mechanical (Repair Instructions 2 Of 3) - 5.7L - Corvette

Helpmelearn

December-24-07 11:03:17 AM

Page 180

Summary of Contents for 5.7L Corvette 2004









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 5.7L Corvette 2004

Reviews:

Related manuals for 5.7L Corvette 2004

Brands by name

Popular brands

Chevrolet 5.7L Corvette 2004, Shop Manual

Search results

Summary of Contents for 5.7L Corvette 2004

Reviews:

Related manuals for 5.7L Corvette 2004

Brands by name

Popular brands