Chevrolet 5.7L Corvette 2004 Shop Manual Download

Page: 701 / 1000

Fig. 173: Inspecting The Camshaft Bearing Journals, Threaded Bolt Holes, Camshaft Valve Lifter
Lobes & Camshaft Sprocket Pin For Damage

Courtesy of GENERAL MOTORS CORP.

1. Clean the components in solvent.

2. Dry the components with compressed air.

3. Inspect the camshaft bearing journals (1) for scoring or excessive wear.

4. Inspect the camshaft valve lifter lobes (2) for scoring or excessive wear.

5. Inspect the threaded bolt holes (3) in the front of the camshaft for damaged threads or debris.

6. Inspect the camshaft sprocket pin (204) for damage.

7. Inspect the camshaft position (CMP) reluctor ring for nicks or damage.

CAUTION: Refer to Safety Glasses Caution in Cautions and Notices.

2004 Chevrolet Corvette

2004 ENGINE PERFORMANCE Engine Mechanical (Repair Instructions 2 Of 3) - 5.7L - Corvette

Helpmelearn

December-24-07 11:03:17 AM

Page 185

Summary of Contents for 5.7L Corvette 2004









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 5.7L Corvette 2004

Reviews:

Related manuals for 5.7L Corvette 2004

Brands by name

Popular brands

Chevrolet 5.7L Corvette 2004, Shop Manual

Search results

Summary of Contents for 5.7L Corvette 2004

Reviews:

Related manuals for 5.7L Corvette 2004

Brands by name

Popular brands