Chevrolet 5.7L Corvette 2004 Shop Manual Download

Page: 711 / 1000

Removal

3. Assemble the tool.

Fig. 182: Bearing & Block Bore

Courtesy of GENERAL MOTORS CORP.

4. Insert the tool through the front of the engine block and into the bearing.

5. Tighten the expander assembly nut until snug.

6. Push the guide cone into the front camshaft bearing to align the tool.

7. Drive the bearing into the block bore.

8. Repeat the above procedures to install the remaining bearings.

TIMING CHAIN AND SPROCKETS CLEANING AND INSPECTION

2004 Chevrolet Corvette

2004 ENGINE PERFORMANCE Engine Mechanical (Repair Instructions 2 Of 3) - 5.7L - Corvette

Helpmelearn

December-24-07 11:03:18 AM

Page 195

Summary of Contents for 5.7L Corvette 2004









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 5.7L Corvette 2004

Reviews:

Related manuals for 5.7L Corvette 2004

Brands by name

Popular brands

Chevrolet 5.7L Corvette 2004, Shop Manual

Search results

Summary of Contents for 5.7L Corvette 2004

Reviews:

Related manuals for 5.7L Corvette 2004

Brands by name

Popular brands