Chevrolet Light Duty Truck 1973 Service Manual Download

Page: 105 / 979

HEATER A N D AIR C O N D IT I O N IN G

1A-79

pressures. Outlet tube restrictions will be indicated by

low head pressures and little or no cooling. An

excessively cold receiver-dehydrator outlet may be

indicative of a restriction.

Expansion Valve

A malfunction of the expansion valve will be caused by

one of the following conditions: valve stuck open, valve

stuck closed, broken power element, a restricted screen or

an improperly located or installed power element bulb.

The first three conditions require valve replacement. The

last two may be corrected by replacing the valve inlet

screen and by properly installing the power element

bulb.

Attachment of the expansion valve bulb to the

evaporator outlet line is very critical. The bulb must be

attached tightly to the line and must make good contact

with the line along the entire length of the bulb. A loose

bulb will result in high low side pressures and poor

cooling.

Indications of expansion valve trouble are provided by

Performance Tests; consult Diagnostic Charts.

VALVE STUCK OPEN

Noisy Compressor.

No Cooling - Freeze Up.

VALVE STUCK CLOSED, BROKEN POWER

ELEMENT OR PLUGGED SCREEN

Very Low Suction Pressure.

No Cooling.

POORLY LOCATED POWER ELEMENT BULB

Normal Pressure.

Poor Cooling.

Diagnosis for Defective Valve

The following procedure must be followed to determine

if a malfunction is due to a defective expansion valve.

1. Check to determine if the system will meet the

performance test as outlined previously. If the

expansion valve is defective, the low pressure

readings (evaporator pressure) will be above

specifications.

2. The loss of system performance is not as evident

when the compressor head pressure is below 200

psi. Therefore, it may be necessary to increase the

system head pressure by partially blocking the

condenser. Disconnect the blower lead wire and

repeat the "performance check" to determine if the

evaporator pressure can be obtained.

3. The system will also indicate a low refrigerant

charge by bubbles occurring in the sight glass.

Evaporator

When the evaporator is defective, the trouble will show

up as an inadequate supply of cool air. A partially

plugged core due to dirt, a cracked case, or a leaking seal

will generally be the cause.

Refrigerant Line Restrictions

Restrictions in the refrigerant lines will be indicated as

follows:

1. Suction Line - A restricted suction line will cause

low suction pressure at the compressor, low

discharge pressure and little or no cooling.

2. Discharge Line - A restriction in the discharge line

generally will cause the pressure relief valve to

open.

3. Liquid Line - A liquid line restriction will be

evidenced by low discharge and suction pressure,

and insufficient cooling.

Sight Glass Diagnosis (G and Motor Home

Chassis Units)

At temperatures higher than 70 degrees F, the sight glass

may indicate whether the refrigerant charge is sufficient.

A shortage of liquid refrigerant is indicated after about

five minutes of compressor operation by the appearance

of slow-moving bubles (vapor) or a broken column of

refrigerant under the glass. Continuous bubbles may

appear in a properly charged system on a cool day. This

is a normal situation. If the sight glass is generally clear

and performance is satisfactory, occasional bubbles do

not indicate refrigerant shortage.

If the sight glass consistently shows foaming or a broken

liquid column, it should be observed after partially

blocking the air to the condenser. If under this condition

the sight glass clears and the performance is otherwise

satisfactory, the charge shall be considered adequate.

In all instances where the indications of refrigerant

shortage continues, additional refrigerant should be

added in 1/4 lb. increments until the sight glass is clear.

An additional charge of 1/2 lb. should be added as a

reserve after the glass clears. In no case should the

system be overcharged.

LIGHT DUTY TRUCK SERVICE MANUAL

Summary of Contents for Light Duty Truck 1973




















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Light Duty Truck 1973

Reviews:

Related manuals for Light Duty Truck 1973

Brands by name

Popular brands

Chevrolet Light Duty Truck 1973, Service Manual

Search results

Summary of Contents for Light Duty Truck 1973

Reviews:

Related manuals for Light Duty Truck 1973

Brands by name

Popular brands