Chevrolet Light Duty Truck 1973 Service Manual Download

Page: 421 / 979

E N G I N E C O O L I N G

6 K -1 1

1. Siphon coolant from the radiator and break loose

the fan pulley bolts.

2. Disconnect heater hose, radiator lower hose and by

pass hose (as required) at water pump.

3. Loosen Delcotron and remove fan belt then remove

fan bolts, fan and pulley.

CAUTION:

If a fan blade is bent or damaged

in any way, no attempt should be made to

repair and reuse the damaged part. A bent or

damaged fan assembly should always be

replaced with a new fan assembly.

It is essential that fan assemblies remain in proper

balance and proper balance cannot be assured once

a fan assembly has been bent or damaged. A fan

assembly that is not in proper balance could fail and

fly apart during subsequent use creating an

extremely dangerous condition.

NOTE: Thermostatic fan clutches must be

kept in an “in-car” position. When removed

from the car the assembly should be

supported so that the clutch disc remains in a

vertical plane to prevent silicone fluid

leakage.

4. Remove pump to cylinder block bolts and remove

pump and old gasket from engine.

NOTE: On in line engines, pull the pump

straight out of the block first, to avoid

damage to impeller.

Installation

1. Install pump assembly on cylinder block then, using

a new, sealer coated, pump-to-block gasket tighten

bolts securely.

2. Install pump pulley and fan on pump hub and

tighten bolts securely.

NOTE: A guide stud (5/16"-24 x 1" bolt with

the head removed) installed in one hole of

the fan will aid in aligning hub, pulley and

fan. Remove stud after starting the remain

ing three bolts.

3. Connect hoses and fill cooling system.

4. Install fan belt and adjust as previously outlined.

5. Start engine and check for leaks.

D IA G N O S IS

If the radiator is filled too full when cold, expansion

when hot will overfill the radiator and coolant will be lost

through the overflow pipe. Adding unnecessary water

will weaken the anti-freeze solution and raise the

temperature at which freezing may occur.

If the cooling system requires frequent addition of water

in order to maintain the proper level in the radiator,

check all units and connections in the cooling system for

evidence of leakage. Inspection should be made with

cooling system cold. Small leaks which may show

dampness or dripping can easily escape detection when

the engine is hot, due to the rapid evaporation of

coolant. Tell-tale stains of grayish white or rusty color, or

dye stains from anti-freeze, at joints in cooling system

are almost always sure signs of small leaks even though

there appears to be no damage.

Air or gas entrained in the cooling system may raise the

level in radiator and cause loss of coolant through the

overflow pipe. Air may be drawn into the cooling system

through leakage at the water pump seal. Gas may be

forced into the cooling system through leakage at the

cylinder head gasket even though the leakage is not

sufficient to allow water to enter the combustion

chamber.

COOLING SYSTEM CHECKS

To check for exhaust leaks into the cooling system, drain

the system until the water level stands just above the top

of the cylinder head, then disconnect the radiator upper

hose and remove the thermostat and fan belt. Start the

engine and quickly accelerate several times. At the same

time note any appreciable water rise or the appearance

of bubbles which are indicative of exhaust gases leaking

into the cooling system.

Water pump operation may be checked by running the

engine while squeezing the radiator upper hose. A

pressure surge should be felt. Check for a plugged vent

hole in pump.
Test for restriction in the radiator, by warming the

engine up and then turning the engine off and feeling

the radiator. The radiator should be hot along the left

side and warm along the right side, with an even

temperature rise from right to left. Cold spots in the

radiator indicate clogged sections.

An operational check of the thermostat can be made by

hanging thermostat on a hook in a 33% glycol solution

25° above the temperature stamped on the thermostat

valve. Submerge the valve completely and igitate the

solution thoroughly. Under this condition the valve

should open. Remove the thermostat and place in a 33%

glycol solution 10° below temperature indicated on the

valve. With valve completely submerged and water

agitated thoroughly, the valve should close completely.

Coolant Loss

1. Make sure owner is not trying to keep radiator

filled to top, and is not filling while cold. The

expansion and contraction of water during opera

tion will cause level to drop below top of filler neck.

LIGHT DUTY TRUCK SERVICE MANUAL

Summary of Contents for Light Duty Truck 1973




















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Light Duty Truck 1973

Reviews:

Related manuals for Light Duty Truck 1973

Brands by name

Popular brands

Chevrolet Light Duty Truck 1973, Service Manual

Search results

Summary of Contents for Light Duty Truck 1973

Reviews:

Related manuals for Light Duty Truck 1973

Brands by name

Popular brands