Chevrolet Light Duty Truck 1973 Service Manual Download

Page: 575 / 979

E N G IN E ELECTRICAL

6 Y -4 7

test show that the resistance can go to .5 ohm before

ignition performance is affected.

B. Insufficient or Excessive Capacity

The condenser specified for use in the ignition system

has a capacity of .18 to .23 microfarads.

If a condenser is used which does not have the specified

capacity of .18 to .23 microfarads, excessive pitting of

one contact point and a corresponding buildup of metal

on the other contact point will result. A condenser having

insufficient capacity will cause build-up of metal on the

breaker arm (positive) point. A condenser having

excessive capacity will cause build-up of metal on the

contact support (negative) point.

In exceptional cases, pitting and metal buildup on

contact points may be experienced even when condenser

capacity is within the specified limits. In such cases the

life of contact points will be improved by installing a

condenser of high-limit capacity if metal build-up is on

breaker arm point, or a condenser of low-limit capacity

if metal build-up is on contact support point. There is

usually sufficient variation in the capacities of stock

condensers to permit selection of a high or low limit

condenser by testing the available stock.

C. Low Insulation Resistance

A weak or leaking condenser is usually one that has

absorbed water so that the insulation resistance of the

winding is lowered to the extent that the condenser will

not hold a charge satisfactorily. A condenser with low

insulation resistance will drain sufficient energy from the

ignition system to lower the secondary voltage seriously.

The condenser specified for use in the ignition system is

sealed to prevent absorption of water, and no other type

should be used.

A leaky condenser usually does not affect engine

performance except when hot. It is unlikely that a

condenser with low insulation resistance would cause

missing at low or medium speeds under conditions where

the condenser does not get hot. A condenser that has low

enough resistance to affect engine performance when

cold would probably be indicated as broken down on

most condenser testers.

Condenser testers equipped to check condensers for low

insulation resistance usually give a reading megohms, a

megohm being one million ohms. The scale is marked to

indicate whether the condenser is good or bad.
When testing a condenser for low insulation resistance

the lead should always be disconnected from the

distributor. Since the distributor terminals and the

connected circuit have much lower insulation resistance

than the condenser, failure to disconnect the condenser

lead will give a reading much too low.

IGNITION SYSTEM RESISTANCE TEST

Check for proper functioning of the resistance in the

primary ignition circuit by turning on the ignition. With

the engine not running, a voltmeter connected from the

battery side of the coil to ground should read

approximately 5 to 5.5 volts. If the reading is a full 12

volts, the ignition points may be open; "bump" the

starter a few times until the engine comes to rest with the

ignition points closed and again check for a 5.5 volt

reading. A reading of 12 volts or over for all engine

positions would indicate that the shorting switch is

making contact all the time; this condition must be

corrected immediately or ignition point life will be very

short.

Check for proper closing of the shorting switch and also

for proper functioning of the complete starting circuit by

grounding the secondary coil wire so the engine won’t

start. With the engine cranking, a voltmeter connected

from the battery side of the coil to ground should read at

least 9 volts. A reading of under 5 bolts would indicate

that the shorting switch is not closing; this condition

would result in hard cold starting.

Briefly, the advantages of our resistance with shorting

switch system are: it sends full battery voltage to the coil

for good cold weather starting, and it cuts down the

voltage to the coil with the engine running for long

ignition point life.

NOTE: Discourage any attempts to measure

voltage at the coil with the engine running;

because of variations in current flow at high

speeds and in regulated voltage, this check

would be meaningless. Voltage readings on a

perfectly-functioning ignition system may go

over 11 volts.

SPARK PLUGS

Under normal operating conditions, spark plugs wear out

due to the destructive action, under intense heat, of

sulphur and lead compounds in the fuel and the

bombardment of the electric spark on the electrodes.

It is reasonable to expect 12,000 miles of useful life from

a spark plug which has been cleaned and regapped at

regular intervals. However, operating conditions are an

important factor and life expectany of the spark plug

will vary with the type of service in which the engine is

used.

The same type of spark plug used in two different

engines of the same make and model may frequently

show wide variation in appearance. The cause of such

differences lies in the condition of the engine, its piston

rings, carburetor setting, kind of fuel used, and under

what conditions the engine is operated, namely,

sustained high speeds or heavy loads; or continual low

speed, stop-and-go driving or light loads.

Spark Plugs are frequently blamed for faulty engine

operation which they do not cause. Replacement of old

spark plugs by new may temporarily improve poor

engine performance because of the lessened demand new

plugs make on the ignition system. This cannot

permanently cure poor engine performance caused by

worn rings or cylinders, weak coil, worn contact points,

faulty carburetion or other engine ills.

On the following pages are pictures of some commonly

encountered appearances and causes • of spark plug

problems.

LIGHT DUTY TRUCK SERVICE MANUAL

Summary of Contents for Light Duty Truck 1973




















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Light Duty Truck 1973

Reviews:

Related manuals for Light Duty Truck 1973

Brands by name

Popular brands

Chevrolet Light Duty Truck 1973, Service Manual

Search results

Summary of Contents for Light Duty Truck 1973

Reviews:

Related manuals for Light Duty Truck 1973

Brands by name

Popular brands