background image

3. 

WHEN USING A HAND-HELD POWER TOOL, ALWAYS MAINTAIN A FIRM 
GRIP ON THE TOOL WITH BOTH HANDS.

4. 

SECURE THE WORKPIECE.

  Whenever possible, secure the workpiece with a 

vise or clamps (not included).

5. 

PRIOR TO STARTING THE INDUSTRIAL ROTARY HAMMER, MAKE SURE TO 
REMOVE THE CHUCK KEY (part #75) FROM THE TOOL.

6. 

AVOID UNINTENTIONAL STARTING.  

Make sure you are prepared to begin 

work before turning on the Industrial Rotary Hammer.

7. 

DO NOT FORCE THE INDUSTRIAL ROTARY HAMMER.  

This tool will do the 

work better and safer at the speed and capacity for which it was designed.  Do 
not force the drill bit or chisel into the workpiece.  Apply moderate pressure, 
allowing the drill bit or chisel to cut without being forced.

8. 

THE INDUSTRIAL ROTARY HAMMER HAS A VARIABLE SPEED (FROM 0 TO 
900 RPM) FEATURE.  

When drilling softer materials or small holes, use a faster 

speed.  When drilling harder materials or larger holes, use a slower speed.

9. 

NEVER LEAVE A POWER TOOL UNATTENDED WHEN IT IS PLUGGED IN 
TO AN ELECTRICAL OUTLET.

 Turn off the tool, and unplug it from its electrical 

outlet before leaving.

10. 

ALWAYS UNPLUG A POWER TOOL FROM ITS ELECTRICAL SUPPLY 
SOURCE BEFORE PERFORMING ANY INSPECTION, MAINTENANCE, OR 
CLEANING PROCEDURES.

11. 

WARNING:

 Some dust created by power sanding, sawing, grinding, drilling, and 

other construction activities, contain chemicals known (to the State of California) 
to cause cancer, birth defects or other reproductive harm.  Some examples of 
these chemicals are: lead from lead-based paints, crystalline silica from bricks 
and cement or other masonry products, arsenic and chromium from chemically 
treated lumber.  Your risk from these exposures varies, depending on how often 
you do this type of work.  To reduce your exposure to these chemicals: work in 
a well ventilated area, and work with approved safety equipment, such as those 
dust masks that are specially designed to filter out microscopic particles.

 

(California Health & Safety Code 25249.5, et seq.)

12. 

WARNING:  

People with pacemakers should consult their physician(s) before 

using this product.  Operation of electrical equipment in close proximity to a heart 
pacemaker could cause interference or failure of the pacemaker.

SKU 02957   

 

 

 

PAGE 5 

 

 

 

REV 03e

Summary of Contents for 02957













Reviews: