background image

Page 6

For technical questions, please call 1-800-444-3353.

SKU 66619 

        

Do not smoke, or allow sparks, flames, 

• 

or other sources of ignition around the 

equipment, especially when refuelling.

Do not refill the Fuel Tank while the 

• 

engine is running or hot.

Do not fill Fuel Tank to the top.  Leave 

• 

a little room for the fuel to expand as 

needed.

Refuel in a well-ventilated area only.

• 

cAUTIoN: 

10. 

This generator is not 

intended to power sensitive electronic 

equipment

*

 without the addition of an 

appropriate line conditioner and surge 

protector (both not included).  Sensitive 

electronic equipment should be operated 

on approved inverter type generators or 

pure sine wave generators.  
If the plugged in product operates 

abnormally or unusually slow, 

immediately stop using the generator 

as a power source.  Always read and 

adhere to the instruction manual of the 

product to be powered, to make sure that 

it can be safely and efficiently powered 

by a portable generator.  

Note:

  When using a generator to 

provide home standby electricity, a 

transfer switch (sold separately) is 

needed to prevent back feeding power 

into the utility line.
Connections for standby power to a 

building electrical system must be made 

by a qualified electrician. The connection 

must isolate the generator power from 

utility power, and must comply with all 

applicable laws and electrical codes.

WARNING:

 Improper connections to 

a building electrical system can allow 

electrical current from the generator 

to backfeed into the utility lines. Such 

backfeed may electrocute utility 

company workers or others who contact 

the lines during a power outage, and the 

generator may explode, burn, or cause 

fires when utility power is restored. 

Consult the utility company or a qualified 

electrician.

*  Sensitive electronic equipment 

includes, but is not limited to, audio/

video equipment, some television sets, 

computers, and printers.

Summary of Contents for 66619


























Reviews: