Chicago Electric 67616 Owner'S Manual And Safety Instructions Download

Page: 8 / 16

Page 8

For technical questions, please call 1-800-444-3353.

Item 67616

Specifications

Electrical Rating

120V~ / 60Hz / 6.5A

Rotational Speed

0-2500 RPM

Impact Rate

0-41,600 BPM

Chuck Capacity

3/64" to 1/2"

Wood Capacity

1" (25mm)

Concrete Capacity

5/8" (16mm)

Steel Capacity

1/2" (13mm)

E194601

39lh

Setup - Before use:

Read the EntiRE impORtant SaFEtY inFORmatiOn section at the beginning of this

manual including all text under subheadings therein before set up or use of this product.

note:

For additional information regarding the parts listed in the following

pages, refer to

Parts List and Diagram

on page 14.

Functions

Figure a

Depth Gauge

Mode Switch

Forward/

Reverse

Switch

Trigger

Lock

Button

Auxiliary

Handle

Chuck

Sa
FE

Op
ER
ati

aint

Enan
CE

tup

Summary of Contents for 67616

















Search results

Summary of Contents for 67616

Reviews:

Related manuals for 67616

Brands by name

Popular brands

Chicago Electric 67616, Owner'S Manual And Safety Instructions

Search results

Summary of Contents for 67616

Reviews:

Related manuals for 67616

Brands by name

Popular brands