background image

Page 15

For technical questions, please call 1-800-444-3353.

Item 68099

        

SAFET

y

Op

ERA

TION

M

AINTENANCE

SETU

p

Limited 90 Day Warranty

Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, 

and warrants to the original purchaser that this product is free from defects in materials and workmanship for the 

period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly, 

to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper 

installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries 

to persons or property, or for incidental, contingent, special or consequential damages arising from the use of 

our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the 

above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER 

WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with transportation charges 

prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise. 

If our inspection verifies the defect, we will either repair or replace the product at our election or we may 

elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will 

return repaired products at our expense, but if we determine there is no defect, or that the defect resulted 

from causes not within the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.

Summary of Contents for 68099

















Reviews: