background image

Page 14

For technical questions, please call 1-800-444-3353.

SKU 68169 

        

Part

Description

Qty.

1

Screw (M6x25)

1

2

Chuck Key

1

3

Chuck

1

4

Spindle

1

5

Spindle Key (3x10mm)

1

6

Circlip (M23)

1

7

Bearing (6002)

1

8

Front Gear

1

9

Back Gear

1

10

Gear box

1

11

Screw (ST4x20)

4

12

Circlip  (M22)

1

13

Oil Seal

1

14

Inner Gear

1

15

Circlip (M12)

1

16

Spring

1

17

Seal Ring

1

18

Oil Seal

1

19

Support

1

20

Bearing (608)

1

21

Rotor

1

22

Bearing (607)

1

23

Impact Selector

1

Part

Description

Qty.

24

Spring Cap

1

25

Spring   

1

26

Mode Selector

1

27

Bearing (607)

1

28

Stator

1

29

Housing 

1

30

O-Ring

1

31

Inductor

1

32

Trigger

1

33

Cord Clamp

1

34

Screw (ST4x14)

2

35

Power Cord

1

36

Cord Sleeve

1

37

Screw (ST2.9x12)

4

38

Carbon Brush

2

39

Brush Holder 

2

40

Direction Switch

1

41

Capacitor

1

42

Screw (ST4x22)

1

43

Housing 

1

44

Screw (ST4.2x16)

6

45

Depth Gauge

1

46

Side Handle

1

PLEASE READ THE FOLLOWING CAREFULLY

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY 

DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY.  NEITHER THE MANUFACTURER OR 

DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE 

OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED 

TO REPLACE ANY PARTS OF THE PRODUCT.  IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR 

EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY 

CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER.  THE BUYER ASSUMES ALL RISK 

AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT 

PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.

PARTS LIST

Record Product’s Serial Number Here: 
Note:

  If product has no serial number, record month and year of purchase instead.

Note:

  Some parts are listed and shown for illustration purposes only, and are not available 

individually as replacement parts.

Summary of Contents for 68169

















Reviews: