background image

SKU 91332 

 

 

    Page 4  

replacement parts. Use of any other parts will void the warranty. Only use 

accessories intended for use with this tool. Approved accessories are 

available from Harbor Freight Tools.

18. 

Do not operate tool if under the influence of alcohol or drugs

.  Read 

warning labels if taking prescription medicine to determine if your judgment 

or reflexes are impaired while taking drugs. If there is any doubt, do not 

operate the tool.

19. 

Maintenance

.  For your safety, service and maintenance should be 

performed regularly by a qualified technician.

20. 

People with pacemakers should consult their physician(s) before 

using this product.

  Electromagnetic fields in close proximity to a heart 

pacemaker could cause interference to or failure of the pacemaker.

In addition, people with pacemakers should adhere to the following:

♦  Avoid operating power tools alone.

♦  Don’t use a power tool with the power switch locked on.

♦  Properly maintain and inspect all tools before use to avoid electrical shock.

Note

: Performance of this tool may vary depending on variations in battery power. 

Warning: The warnings, cautions, and instructions discussed in this instruc-

tion manual cannot cover all possible conditions and situations that may oc-

cur. It must be understood by the operator that common sense and caution 

are factors which cannot be built into this product, but must be supplied by 

the operator.

Unpacking

When unpacking, check to make sure the that all following parts are included. If 

any parts are missing or broken, please call Harbor Freight Tools at the number 

on the cover of this manual.

Cordless 

Screwdriver

Charger 

Adapter

Accessory Bits

and Adapters

Summary of Contents for 91332









Reviews: