Chicago Electric 91772 Assembly And Operating Instructions Manual Download

Page: 10 / 15

SKU 91772

For technical questions, please call 1-800-444-3353.

Page 10

UNPACKING

When unpacking, check to make sure all the parts shown on the

Parts List on page 14

are included. If any parts are missing or broken, please call Harbor Freight Tools at the
number shown on the cover of this manual as soon as possible.

ASSEMBLY AND OPERATING INSTRUCTIONS

NOTE:

For additional information regarding the parts listed in the following pages, refer

to the

Assembly Diagram

page 15

CAUTION:

Always make sure the Power Cord of the Sprayer is unplugged from

its electrical outlet

prior to making any adjustments to the tool.

FIGURE 1

Gun Body (27)

Spiral Air Hose (46)

Paint Cup (24)

Cup Cover (19)

Strap (28)

Motor Unit

Inflator (32)

Viscosity Cup (33)

Summary of Contents for 91772
















Search results

Summary of Contents for 91772

Reviews:

Related manuals for 91772

Brands by name

Popular brands

Chicago Electric 91772, Assembly And Operating Instructions Manual

Search results

Summary of Contents for 91772

Reviews:

Related manuals for 91772

Brands by name

Popular brands