background image

SKU 93449

For technical questions please call 1-800-444-3353

Page 4

15.

Guard against electric shock

.  Prevent body contact with grounded surfaces

such as pipes, radiators, ranges, and refrigerator enclosures.

16.

Replacement parts and accessories

.  When servicing, use only identical

replacement parts. Use of any other parts will void the warranty. Only use
accessories intended for use with this tool. Approved accessories are
available from Harbor Freight Tools.

17.

Do not operate tool if under the influence of alcohol or drugs

.  Read

warning labels on prescriptions to determine if your judgment or reflexes are
impaired while taking drugs. If there is any doubt, do not operate the tool.

18.

Maintenance

.  For your safety, service and maintenance should be performed

regularly by a qualified technician.

19.

Pacemaker safety warning

. People with pacemakers should consult with

their physician(s) before using this product; operation of equipment in close
proximity to a heart pacemaker could cause interference or failure of the
pacemaker.

Note

: Performance of the charger may vary depending on variations in local line volt-

age. Extension cord usage may also affect tool performance.

Warning: The warnings, cautions, and instructions discussed in this instruc-
tion manual cannot cover all possible conditions and situations that may oc-
cur. It must be understood by the operator that common sense and caution
are factors which cannot be built into this product, but must be supplied by
the operator.

Summary of Contents for 93449













Reviews: