SKU 93632
For technical questions, please call 1-800-444-3353.
English
Page 10
PARTS LIST
#
t
r
a
P
n
o
i
t
p
i
r
c
s
e
D
.
Y
T
Q
#
t
r
a
P
n
o
i
t
p
i
r
c
s
e
D
.
Y
T
Q
1
5
m
r
e
h
s
a
W
g
n
i
r
p
S
4
9
2
r
o
t
a
t
S
1
2
0
5
5
x
5
T
S
w
e
r
c
S
4
0
3
b
o
n
K
e
l
d
n
a
H
e
d
a
p
S
1
3
y
e
K
k
c
u
h
C
1
1
3
e
l
d
n
a
H
e
d
a
p
S
1
4
2
2
x
6
m
w
e
r
c
S
d
a
e
H
p
a
C
1
2
3
e
s
a
C
k
c
a
B
1
5
k
c
u
h
C
1
3
3
p
a
C
h
s
u
r
B
2
6
1
2
m
r
e
h
s
a
W
1
4
3
h
s
u
r
B
n
o
b
r
a
C
2
7
g
n
i
s
u
o
H
r
a
e
G
1
5
3
r
e
d
l
o
H
h
s
u
r
B
2
8
3
m
n
i
P
2
6
3
8
m
t
u
N
x
e
H
1
9
S
R
2
0
0
6
g
n
i
r
a
e
B
ll
a
B
1
7
3
t
u
N
r
o
f
r
e
v
o
C
1
0
1
p
il
c
r
i
C
1
8
3
F
6
1
x
4
T
S
w
e
r
c
S
4
1
1
0
1
x
7
.
3
x
3
m
y
e
K
3
9
3
g
n
i
s
u
o
H
1
2
1
e
l
d
n
i
p
S
1
0
4
e
v
e
e
l
S
r
e
b
b
u
R
1
3
1
r
a
e
G
t
u
p
t
u
O
1
1
4
g
u
l
P
d
n
a
d
r
o
C
1
4
1
0
4
x
0
1
m
w
e
r
c
S
1
2
4
p
il
C
d
r
o
C
1
5
1
e
l
d
n
a
H
e
d
i
S
1
3
4
6
1
x
4
T
S
w
e
r
c
S
2
6
1
2
1
m
p
il
c
r
i
C
1
4
4
r
e
v
o
C
e
l
d
n
a
H
1
7
1
2
1
4
1
0
1
K
H
g
n
i
r
a
e
B
e
l
d
e
e
N
1
5
4
F
8
1
x
4
T
S
w
e
r
c
S
2
8
1
t
f
a
h
S
d
n
o
c
e
S
1
6
4
h
c
t
i
w
S
1
9
1
r
a
e
G
d
n
o
c
e
S
1
7
4
e
t
a
l
P
e
p
y
T
1
0
2
2
1
m
p
il
c
r
i
C
1
8
4
0
5
5
x
4
T
S
w
e
r
c
S
2
1
2
0
1
2
1
8
0
K
H
g
n
i
r
a
e
B
e
l
d
e
e
N
4
9
4
e
t
a
l
P
e
m
a
N
1
2
2
r
e
v
o
C
g
n
i
s
u
o
H
r
a
e
G
1
0
5
Z
2
.
0
0
0
6
g
n
i
r
a
e
B
ll
a
B
1
3
2
0
1
m
p
il
c
r
i
C
1
1
5
g
n
i
R
-
O
1
4
2
r
e
n
i
a
t
e
R
g
n
i
r
a
e
B
1
2
5
g
n
i
R
l
a
e
S
1
5
2
e
r
u
t
a
m
r
A
1
3
5
r
a
e
G
t
s
r
i
F
1
6
2
7
2
.
8
0
6
g
n
i
r
a
e
B
ll
a
B
1
4
5
t
f
a
h
S
t
s
r
i
F
1
7
2
g
n
i
h
s
u
B
g
n
i
r
a
e
B
1
5
5
t
e
k
s
a
G
1
8
2
e
d
i
u
G
g
n
i
d
n
i
W
1
NOTE: Some parts are listed and shown for illustration purposes only and are not available individually as
replacement parts.
TROUBLESHOOTING
1.
Drill operates but hole is not effectively drilled.
Possible Cause: Inappropriate or dull drill bit. Solution: Try a different drill bit.
2.
Drill will not turn ON.
Possible Cause: No power source. Solution: Check that the power cord is plugged into an appropriate live
outlet. Check that power cord is in good condition.
Possible Cause: Damaged Carbon Brushes. Solution: Unplug tool. Remove and inspect Carbon Brushes.
If glazed, they can be cleaned with a pencil eraser. If chipped, cracked or worn out, they must be
replaced. Reinstall good Carbon Brushes. Plug in tool and try again.
Possible Cause: Damaged or burned out Rotor or Stator. Solution: Take to a qualified service technician
for replacement or repair.
3.
Drill bit “wobbles” in Chuck.
Possible Cause: Loose or misaligned drill bit. Solution: Unplug tool from power supply. Loosen drill bit in
chuck, and reinstall carefully. Tighten securely.
Possible cause: Chuck is loose on Spindle (12). Solution: Tighten the Chuck onto the Spindle by turning
clockwise.
